DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Windows and Doors > 27" interior door?




Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old 07-26-2014, 07:40 AM  
papakevin
Member
 
Join Date: Oct 2011
Location: Jeffersonville, IN / Louisville, KY
Posts: 87
Liked 4 Times on 4 Posts

Default 27" interior door?

Forgive the basic post, but in not much on finished carpentry work. Purchased a house and I have a unique situation and I'm seeking some assistance.

In the new house, there is no door between the master bedroom and master bath and the opening measures 27". All the door frames in the house has unique molding, so I'm not looking to year them out or replace the framing. I purchased a pre drilled six 28" panel door (I hate drilling in door knobs) and figured I'd cut an inch off the back, but ended up cutting off the 1x1 in the hollow door which the hinges would mount to, so that didn't work out. Was thinking I could glue and clamp another one back in, but not sure that will work.

Is my best option to buy another 28" door and use a planer to equally take down both sides? Should I buy a 26" door and build up the sides of the frame with 1/2" plywood? Other thoughts?

If it wasn't for the special molding in the house, I would just purchase a pre hung door and call it a day.

Thanks for the thoughts.





Sent from my iPhone using Home Repair



__________________
papakevin is offline  
 
Reply With Quote Quick reply to this message
Old 07-26-2014, 07:55 AM  
havasu
on permanent vacation
HRT_LIFETIMESUPPORTER.png
 
havasu's Avatar
 
Join Date: Oct 2010
Location: Southern California, CA
Posts: 1,984
Liked 87 Times on 75 Posts
Likes Given: 24

Default

Unless you trim both sides 1/2", your six panels will look lopsided.



__________________
havasu is offline  
 
Reply With Quote Quick reply to this message
Old 07-26-2014, 10:08 AM  
beachguy005
Senior Member
 
Join Date: Sep 2012
Posts: 137
Liked 33 Times on 31 Posts

Default

Trying to trim both sides..with a planer.....how square do you thing that door would end up? Getting a prehung, even though the trim won't match the rest of the house, is probably your best bet.
You can get one without attached trim, or just pull it off, then try to match it as best you can with the rest of the house. Given that it's a MB, how much of an esthetic issue would it really be if it wasn't exactly like the casings in the rest of your house?

__________________
beachguy005 is offline  
 
Reply With Quote Quick reply to this message
Old 07-26-2014, 01:34 PM  
bud16415
Fixer Upper
 
bud16415's Avatar
 
Join Date: Feb 2013
Location: Erie Pa, Pa
Posts: 1,028
Liked 294 Times on 231 Posts
Likes Given: 102

Default

I would buy the wider door and take equal amounts off each side. .5 inch is a bit much to take off that way. I would use table saw or skill saw with rip fence. Then belt sand or sand by hand. Anything under 27 will start to feel tight walking thru. One thought is to use a self centering spring hinges and you won't have to drill for latches etc into your trim. The door could swing both ways and always stay shut. Just a thought for a bath attached to a master.


Sent from my iPhone using Home Repair

__________________
bud16415 is online now  
 
Reply With Quote Quick reply to this message
Old 07-26-2014, 03:19 PM  
Wuzzat?
Senior Member
 
Wuzzat?'s Avatar
 
Join Date: Jan 2010
Posts: 2,297
Liked 164 Times on 151 Posts
Likes Given: 89

Default

The door knob hardware has to accommodate the door edge to hole center distance.

__________________
Wuzzat? is offline  
 
Reply With Quote Quick reply to this message
Old 07-26-2014, 03:47 PM  
oldognewtrick
Moderator
HRT_MODERATOR.png
 
oldognewtrick's Avatar
 
Join Date: Jul 2009
Location: Nashville, TN
Posts: 4,753
Liked 377 Times on 314 Posts
Likes Given: 123

Default

Let me throw this out, what about bi-fold doors?

__________________
oldognewtrick is offline  
 
Reply With Quote Quick reply to this message
Old 07-28-2014, 05:06 PM  
slownsteady
Supporting Member
HRT_SUPPORTER.png
 
slownsteady's Avatar
 
Join Date: Jun 2009
Location: Newton, NJ
Posts: 841
Liked 118 Times on 101 Posts
Likes Given: 145

Default

You might have to take a peak under the trim to find out the rough opening dimensions. With a little luck the rough is a standard number. Then with a little TLC, you might be able to re-use the trim or match it.

__________________
slownsteady is offline  
 
Reply With Quote Quick reply to this message
Old 07-28-2014, 06:27 PM  
nealtw
Contractor
 
Join Date: Nov 2010
Location: vancouver, b.c.
Posts: 9,441
Liked 747 Times on 667 Posts
Likes Given: 1303

Default

Find a good door supplier and have them modify the door, to take that much off both sides, the solid wood on both sides sould be removed and re-installed deeper so the hardwear has something to screw to.



__________________
nealtw is online now  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Interior door fiasco Frank0 Carpentry and Woodworking 6 08-05-2014 05:10 PM
"Bulkhead" Basement Door dpg1961 Windows and Doors 6 09-07-2012 10:30 AM
34" interior door pionier Windows and Doors 1 08-13-2009 06:23 PM
25" Interior Doors bootpdx Windows and Doors 3 02-07-2008 06:47 PM
Getting stains off a "molded" door? WestBentley Windows and Doors 4 01-17-2007 07:00 AM