DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Windows and Doors > interior door problem




Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old 11-28-2009, 08:16 PM  
1989gta
Junior Member
 
Join Date: Oct 2006
Posts: 24
Default interior door problem

i'm hanging a pre hung door after finishing and hanging the door, it sags creating a large gap at the top but the jamb is still plumb what gives?

The steps i took are as follows:

1. Placed the jamb in the rough opening, marked where the hinges will fall.
2. I screwed shims to the wall (jamb side) checking plumb with a 6 ft level
3. Placed the jamb back in the opening and secured it using 2.5 inch screws checking for plumb on both the face and the side of the jamb.
4. Hung the door back on the jamb checking the gap and the swing prior to nailing the latch side.

How do i adjust how the door sits against the jamb i need to tighten to top? You can see by the red arrows the gap is 2 or 3x's larger on the top then on the bottom.



__________________

nick

1989gta is offline  
 
Reply With Quote Quick reply to this message
Old 11-29-2009, 11:08 AM  
1989gta
Junior Member
 
Join Date: Oct 2006
Posts: 24
Default

I've tried driving the screws on the top hinge further into the jamb. - no change
I pounded shims into the upper left hand corner shifting the jamb header it helped but was not enough.
As a last resort i will loosen the joint between the jamb header and the latch side (upper right hand corner) to gain the 1/8 inch of clearance needed unless someone has other thoughts.

Another thought but undesirable is to remove the door and increase the mortise on the top hing an 1/16 of an inch that may cause other issues.

Thanks for viewing.



__________________

nick

1989gta is offline  
 
Reply With Quote Quick reply to this message
Old 01-18-2010, 03:26 PM  
GregC
Quick Belt System
 
Join Date: Jan 2010
Posts: 82
Default Pre-Hung door reveal

Hello, If all is plumb and square then the quick fix to carry some reveal(gap) down the door is go to the bottom hinge and place small cardboard shim or shims as needed behind the hinges. This will pack the lower hinge away from the door jamb. Now granted, as long as you have enough reveal(gap) on the strike side so the door does not hit and bang. Its hard to see with your photo if you have enough of a reveal on strike side. Make sure the door is "racked" properly as well. Not sure if you know how to but just in case, measure from top left to bottom right, then measurement should be same from bottom left to top right. Hope this helps. Greg

__________________

GregC, President/Founder [COLOR="Blue"]www.Quicktoolbeltsystem.com[/COLOR]

GregC is offline  
 
Reply With Quote Quick reply to this message
Old 02-14-2010, 08:36 PM  
Doorguy4ya
door guy 4 ya
 
Join Date: Feb 2010
Posts: 27
Send a message via Yahoo to Doorguy4ya
Default

if its a pre hung door, simply shim the bottom of the frames to take up the gap at the top.

__________________
Doorguy4ya is offline  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Interior door problem bsmutz Windows and Doors 1 08-15-2009 01:57 PM
34" interior door pionier Windows and Doors 1 08-13-2009 06:23 PM
Garage Door Opener problem generic703 Windows and Doors 6 01-14-2009 09:35 PM
Shower door frame problem jgalt Windows and Doors 1 01-02-2009 09:53 PM
Interior door installation teaklumber Windows and Doors 2 02-05-2008 09:30 AM