DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Painting Forum > hopefully I didn't screw up in repainting a corrugated metal roof





Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old 10-16-2010, 09:28 AM  
MelonieNY
Junior Member
 
Join Date: Oct 2010
Location: New York, New York
Posts: 4
Default hopefully I didn't screw up in repainting a corrugated metal roof

Hello everyone. I wish that I had found this forum before embarking on this project, but better late than never. At any rate, I'm looking for opinions as to whether I screwed up or not during a recent repainting of my metal house roof.

The story begins when I replaced my dilapidated asphalt shingle garage roof with new pre-painted ( blue ) 'full length' corrugated metal. This came out excellent, but it made the ~50 year old sectional ( green ) corrugated metal roof on my main house look even worse in comparison. I priced out a similar replacement with new pre-painted 'full length' corrugated metal on the main house roof, but the 1600 sq ft required priced this option off the table.

The existing sectional metal main house roof had occasionally leaked, but this was always due to the gasketed roofing nails securing the metal sheeting working loose. Other than surface rust here and there, the metal sheeting itself was in fairly good shape. So repainting at perhaps 20% of replacement cost seemed like a viable option.

I began by pounding down all of the existing gasketed roofing nails, plus installing new self-tapping roof screws in between the existing nails. I then did a wash with brush scrub using a mildew / stain remover ( specifically Behr #62). After rinsing, I then did a diluted acid etch in order to remove as much surface oxide as I could ( specifically Behr #991). The acid etch showed up all of the old roofing nail gaskets which had degraded over time ... which I then simply wire brushed away and hammered down flat.

After another rinse and dry, I then applied a reasonably thick layer of exterior primer ( specifically Behr #436) over the top of everything, including the heads of the new screws and existing roofing nails. I followed this up with two coats of 100% acrylic latex roof paint ( specifically Behr #66 deep base tinted to match my new blue pre-painted garage roof )

My concern here is that the original ~50 year old sectional steel roof appears to have relied on the gasketed roofing nail approach to handle expansion and contraction of the individual metal sheets. By securing all of these metal sheets much more 'tightly' to the underlying roof boards via the extra screws ( which I had to do to stop additional potential leaks from the ~50 year old nail gaskets continuing to fail), I am now basically relying on the elasticity of the new roof primer and paint to absorb expansion and contraction. In other words, with gasketed nails only, the separate steel sheets were able to 'move' a little bit in relation to each other as they expanded and contracted. But now that they are screwed down tightly, it's probable that thermal expansion will result in the steel sheets having to 'hump up' a bit between the vertical rows of screws / nails.

Your thoughts and recommendations would be greatly appreciated.



__________________

Last edited by MelonieNY; 10-16-2010 at 09:40 AM.
MelonieNY is offline  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Metal Roof - Seal or Rescrew TxBuilder Roofing and Siding 1 09-15-2010 12:53 PM
Sealing Metal Roof Screws TxBuilder Roofing and Siding 2 12-30-2009 01:41 PM
Metal roof procedure ? Mudball Roofing and Siding 14 09-26-2007 02:56 PM
Metal roof and pest mdejon Roofing and Siding 0 07-02-2006 10:02 AM
Metal Roof Problems birch Roofing and Siding 4 03-13-2006 11:13 AM