DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Walls and Ceilings > 61" bathroom to 60"




Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old 01-13-2014, 04:09 PM  
swindmill
Senior Member
 
Join Date: Jan 2010
Posts: 167
Liked 12 Times on 11 Posts
Likes Given: 1

Default 61" bathroom to 60"

I'm remodeling a bathroom with the tub against the back wall. The old tub was 61", and the new tub is a standard 60". The walls around the tub will get CBU and tile. The tub is in place but I need to fur out the right hand wall an inch (lefthand tub). I'm look for ideas on how to best handle this. Everything I can think of is 3/4 or 1/2.



__________________
swindmill is offline  
 
Reply With Quote Quick reply to this message
Old 01-13-2014, 04:22 PM  
Wuzzat?
Banned
 
Join Date: Jan 2010
Posts: 2,328
Liked 167 Times on 154 Posts
Likes Given: 94

Default

Long shim strips?



__________________
Wuzzat? is offline  
 
Reply With Quote Quick reply to this message
Old 01-13-2014, 04:38 PM  
swindmill
Senior Member
 
Join Date: Jan 2010
Posts: 167
Liked 12 Times on 11 Posts
Likes Given: 1

Default

I'm hoping to just shim out each stud 1", I just don't know what material to use. I don't have a table saw that will allow me to rip my own strips, so I'm stuck using stock material. If there's nothing available, it may just be time to get a decent table saw. I'd like to have one, so if I have to get one...

__________________
swindmill is offline  
 
Reply With Quote Quick reply to this message
Old 01-13-2014, 04:55 PM  
nealtw
Contractor
 
Join Date: Nov 2010
Location: vancouver, b.c.
Posts: 10,258
Liked 844 Times on 754 Posts
Likes Given: 1461

Default

Pick up a half sheet of 1" plywood or rip 2x4 down to get 1 1/2 x1 strips.

__________________
nealtw is offline  
 
Reply With Quote Quick reply to this message
Old 01-13-2014, 05:20 PM  
swindmill
Senior Member
 
Join Date: Jan 2010
Posts: 167
Liked 12 Times on 11 Posts
Likes Given: 1

Default

I guess I've never looked for 1" plywood, but if the big box stores carry it, that would work.

__________________
swindmill is offline  
 
Reply With Quote Quick reply to this message
Old 01-13-2014, 05:22 PM  
oldognewtrick
Moderator
HRT_MODERATOR.png
 
oldognewtrick's Avatar
 
Join Date: Jul 2009
Location: Nashville, TN
Posts: 5,412
Liked 459 Times on 382 Posts
Likes Given: 145

Default

Or a double layer of 1/2"...

__________________
oldognewtrick is offline  
 
Reply With Quote Quick reply to this message
Old 01-13-2014, 05:55 PM  
nealtw
Contractor
 
Join Date: Nov 2010
Location: vancouver, b.c.
Posts: 10,258
Liked 844 Times on 754 Posts
Likes Given: 1461

Default

If the wall come out and stop at an outside corner, where you might want to put up corner bead for drywall, don't use plywood , it messes up with the screws for the cornerbead.

__________________
nealtw is offline  
 
Reply With Quote Quick reply to this message
Old 01-13-2014, 07:23 PM  
CallMeVilla
Contractor
 
CallMeVilla's Avatar
 
Join Date: Feb 2010
Location: San Diego
Posts: 1,272
Liked 388 Times on 304 Posts
Likes Given: 161

Default

Your best bet is to cut 1" shims from a 2x6. Put two of them side by side to create a steady base for the skill saw as you cut the strips.

Now you will have a good shim for corner bead nailing. This is better than buying milled 1" casing ... and a lot cheaper!

tub-framing.jpg  
__________________
CallMeVilla is online now  
 
Reply With Quote Quick reply to this message
Old 01-14-2014, 08:15 AM  
bud16415
Fixer Upper
 
bud16415's Avatar
 
Join Date: Feb 2013
Location: Erie Pa, Pa
Posts: 1,232
Liked 352 Times on 282 Posts
Likes Given: 115

Default

I nail my corner bead on and haven’t had any issues with plywood or OSB even. I just use drywall nails as the heads are so thin they don’t stick up and don’t bend the bead like screws will want to.

Without a table saw it’s still not so hard to rip stock with a hand circular saw if you take your time. I often screw a guide strip to the piece I’m ripping similar to what Villa suggests. I find a nice straight piece of trim wood works better than a 2X as the 2X has a round corner and my saw wants to get stuck in that corner. I bought a thing called a workmate last summer at a garage sale and I love it for holding a long piece to rip like this.

I would cut two strips of half as oldog suggests.

__________________
bud16415 is offline  
 
Reply With Quote Quick reply to this message
Old 01-14-2014, 09:59 AM  
swindmill
Senior Member
 
Join Date: Jan 2010
Posts: 167
Liked 12 Times on 11 Posts
Likes Given: 1

Default

I could rip 2x with some clamps and a guide. Doubling up 1/2" would work too. I'll be going with one of those options in the next few days.



__________________
swindmill is offline  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Septic field "perc" test, Sq. Hole digging suggestions. WallyPop General Home Improvement Discussion 8 08-30-2012 08:55 PM
Difference between "baseboards" and "moulding" panzerfaust0 Walls and Ceilings 8 01-18-2012 01:55 AM
System running Hot while set to "Cool" & "Off" halogen49 HVAC 7 03-06-2011 04:42 PM
Replacing main water supply line.......with "help" from lowes >< BhodiLi Plumbing Forum 2 11-14-2009 08:10 AM
"Post Your Bathroom" thread BantyMom HouseRepairTalk Website Help 0 08-05-2009 11:40 PM