DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Walls and Ceilings > Crown molding




Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old 12-13-2012, 06:54 PM  
jmc0319
Senior Member
 
Join Date: Jun 2012
Posts: 279
Liked 31 Times on 22 Posts
Likes Given: 5

Default Crown molding

So I am about to start my first crown molding project. Any suggestions appreciated.

Thanks



__________________
jmc0319 is offline  
 
Reply With Quote Quick reply to this message
Old 12-13-2012, 07:53 PM  
nealtw
Contractor
 
Join Date: Nov 2010
Location: vancouver, b.c.
Posts: 10,257
Liked 844 Times on 754 Posts
Likes Given: 1461

Default

The bigger the molding the bigger the nightmare. So how big is the molding and what saw do you have to cut it with?



__________________
nealtw is offline  
 
Reply With Quote Quick reply to this message
Old 12-14-2012, 05:33 AM  
jmc0319
Senior Member
 
Join Date: Jun 2012
Posts: 279
Liked 31 Times on 22 Posts
Likes Given: 5

Default Crown molding

I haven't decided yet but I think I will go with something small. Probably like 2 - 3". I have a compound mitre saw that I am fairly comfortable with. I tried reading about molding but there is a lot of conflicting info out there.

__________________
jmc0319 is offline  
 
Reply With Quote Quick reply to this message
Old 12-14-2012, 07:41 AM  
nealtw
Contractor
 
Join Date: Nov 2010
Location: vancouver, b.c.
Posts: 10,257
Liked 844 Times on 754 Posts
Likes Given: 1461

Default

The table of the saw is the ceiling and build a jig that will hold the molding on the correct angle against the fence. Just build a box like the old handsaw jig, but to fit the molding. Bosch makes a neet angle finder. Drywalled corners are never square.
https://www.rona.ca/en/angle-finder---4-in-1-angle-finder#
Once you have that you just have to remmember that everything is upside down and backwards.
If you go with a molding to big to stand up like that you have to set both angles on the saw and that gets really tough.

__________________
nealtw is offline  
 
Reply With Quote Quick reply to this message
Old 12-14-2012, 08:12 AM  
jmc0319
Senior Member
 
Join Date: Jun 2012
Posts: 279
Liked 31 Times on 22 Posts
Likes Given: 5

Default

Great thanks Neal.

__________________
jmc0319 is offline  
 
Reply With Quote Quick reply to this message
Old 12-14-2012, 08:18 AM  
jmc0319
Senior Member
 
Join Date: Jun 2012
Posts: 279
Liked 31 Times on 22 Posts
Likes Given: 5

Default

One question Neal. Say I use the angle finder and it shows the wall to be at 87 degrees instead of 90. How would I then cut the molding to fit? Also should I cope or not?

__________________
jmc0319 is offline  
 
Reply With Quote Quick reply to this message
Old 12-14-2012, 08:35 AM  
nealtw
Contractor
 
Join Date: Nov 2010
Location: vancouver, b.c.
Posts: 10,257
Liked 844 Times on 754 Posts
Likes Given: 1461

Default

I never cope crown but could on the inside corners. for 87 degrees, you cut both sides to 43.5. Just divide in half. The bosch square will give you the answer. It would would read 43.5.
Learning how to cut the stuff is just the start, accurate measurement are just as important. And then placement on the wall is critical, any little bit up or down really screws the angle up.

__________________
nealtw is offline  
 
Reply With Quote Quick reply to this message
Old 12-14-2012, 09:11 AM  
jmc0319
Senior Member
 
Join Date: Jun 2012
Posts: 279
Liked 31 Times on 22 Posts
Likes Given: 5

Default One last question (maybe)

Great info thanks Neal. Is coping the inside corners easier for someone like me?

__________________
jmc0319 is offline  
 
Reply With Quote Quick reply to this message
Old 12-14-2012, 09:43 AM  
nealtw
Contractor
 
Join Date: Nov 2010
Location: vancouver, b.c.
Posts: 10,257
Liked 844 Times on 754 Posts
Likes Given: 1461

Default

I never found it easier to cope, but I don't do alot of this stuff. Just try a few samples and see what your comfortable with.

__________________
nealtw is offline  
 
Reply With Quote Quick reply to this message
Old 12-19-2012, 02:53 PM  
Housedoctor57
Member
 
Join Date: Mar 2010
Posts: 40
Liked 4 Times on 4 Posts

Default

I used a thermal label maker and put a label on my miter saw reminding me of inside and outside corner "good" side so I have 1 less thing to remember in my head. Helps me out a lot.



__________________
Housedoctor57 is offline  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Removing crown molding daytona Walls and Ceilings 1 08-06-2012 12:13 PM
Crown molding billyo Carpentry and Woodworking 12 06-30-2012 09:09 PM
Crown Molding, Kitchen cabinets powersro Carpentry and Woodworking 6 02-07-2011 07:51 PM
Crown Molding - Going Bananas! sharper Carpentry and Woodworking 5 09-19-2008 10:10 PM
How to cut crown molding spyder9176 Carpentry and Woodworking 7 03-04-2008 10:13 AM