DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Walls and Ceilings > H shealthing clips--1/2 inch for 7/16 OSB





Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old 03-24-2011, 02:19 PM  
HighDesertHomeOwner
Junior Member
 
Join Date: Nov 2010
Location: Los Angeles, CA
Posts: 26
Default H shealthing clips--1/2 inch for 7/16 OSB

Home Depot does not sell 7/16 H clips for 7/16 OSB. They only have 1/2 inch.

Would 1/2 inch be too loose for 7/16 OSB?



__________________
HighDesertHomeOwner is offline  
 
Reply With Quote Quick reply to this message
Old 03-24-2011, 03:14 PM  
inspectorD
Housebroken
 
inspectorD's Avatar
 
Join Date: Dec 2005
Location: Litchfield, CT
Posts: 3,906
Liked 82 Times on 71 Posts
Likes Given: 157

Default well

There is a reason for that...your not supposed to use 7/16 OSB for a roof.
Your going to fall through, crack shingles and create small leaks.
Buy only 1/2 inch 5 ply exterior rated exposure plywood for roofs. Otherwise, your shingles will not be warranteed.
Just tryin to save you trouble down the road.



__________________

Just My
Made in the

inspectorD is offline  
 
Reply With Quote Quick reply to this message
Old 03-24-2011, 03:25 PM  
nealtw
Senior Member
 
Join Date: Nov 2010
Location: vancouver, b.c.
Posts: 7,675
Liked 538 Times on 488 Posts
Likes Given: 998

Default

7/16 is min. code here and it,s pritty standard but always use "H" clips one size up to make life easier when installing.

__________________
nealtw is offline  
 
Reply With Quote Quick reply to this message
Old 03-27-2011, 07:38 AM  
joecaption
Senior Member
 
Join Date: Jan 2011
Location: Hartfield VA, VA
Posts: 1,359
Liked 36 Times on 31 Posts
Likes Given: 2

Default

7/16 clips is the correct size for 1/2 OSB, In fact if you check you will find there's no such thing as real 1/2 think OSB.
I have not seen plywood used on roofs for many many years. And any roof I've seen done or have done myself has been done with 7/16". As long as you use the H clips it works fine.
The main reason not to use plywood is if it delaminates the roof will be full of humps.
Plywood may be code in a hurracane area, with full headed nails.

__________________
joecaption is offline  
 
Reply With Quote Quick reply to this message
Old 03-28-2011, 10:16 AM  
HighDesertHomeOwner
Junior Member
 
Join Date: Nov 2010
Location: Los Angeles, CA
Posts: 26
Default

I have never seen true 1/2 inch plywood or OSB at HD or anywhere.

Only MDF or particle board is true dimension thickness, ie nominal and actual are the same.

At HD, it says 7/16 OSB.

__________________
HighDesertHomeOwner is offline  
 
Reply With Quote Quick reply to this message
Old 03-28-2011, 10:23 AM  
HighDesertHomeOwner
Junior Member
 
Join Date: Nov 2010
Location: Los Angeles, CA
Posts: 26
Default

Are H-clips intended only for the roof and not for side shealthing?

I read that they are for both so I intended to use them for both the sides and the roof.

I had wanted to use 14.5" long 2x4 spacers to attach shealthing at 48" intervals, but changed my mind as the H-clips are easier and cheaper.

__________________
HighDesertHomeOwner is offline  
 
Reply With Quote Quick reply to this message
Old 03-29-2011, 12:00 AM  
nealtw
Senior Member
 
Join Date: Nov 2010
Location: vancouver, b.c.
Posts: 7,675
Liked 538 Times on 488 Posts
Likes Given: 998

Default

"H" clips are used to spread the load on the roof when you walk on it, when rafters are at 24" on center the edge of plywood or osb will bend and the roofing shingles are likely to be damaged. Osb should never be smaller than the measurement that is stamped on it. It often swells 1/8 " if or when exposed to rain. Thinner sheets should be sent back or used elseware but not on the roof.



__________________
nealtw is offline  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
3 inch dryer vent Djshakes General Home Improvement Discussion 3 03-10-2010 02:50 PM
32 inch door in a 30 inch space? TaskBoy Windows and Doors 15 06-14-2008 09:05 AM
1/2 inch pex to shower outnabout Plumbing Forum 3 10-26-2007 11:21 PM
Engineered wood floor over subfloor with clips Jaybird VuCE Flooring 3 12-16-2006 12:04 PM
24 inch to 16 inch Centers dsearles Framing and Foundation 1 04-04-2006 10:58 PM