DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Walls and Ceilings > How to install PVC 4x8 sheets on a ceiling




Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old 04-04-2012, 04:29 PM  
cmerk16
Junior Member
 
Join Date: Mar 2012
Posts: 10
Default How to install PVC 4x8 sheets on a ceiling

I'm putting PVC 4x8 sheets on the ceiling outside to a front door (alcove). After their installed, tongue and grove boards will go on the side (vertically). When I install the ceiling I will use construction adhesive to go against the joist. My question is how do I go about nailing? My initial thought was to use a trim gun and making sure the setting didn't blast through the PVC sheets. But I'm a little concerned that may not work. The reason I'm using PVC is to create less maintenance in the future. I will never have to replace the sheets unless they crack, all I may have to do is repaint.



image-299206730.jpg  
__________________
cmerk16 is offline  
 
Reply With Quote Quick reply to this message
Old 04-04-2012, 04:55 PM  
kok328
Supporting Member
HRT_SUPPORTER.png
 
Join Date: Nov 2007
Location: Grand Blanc, MI
Posts: 2,195
Liked 112 Times on 97 Posts
Likes Given: 64

Default

PVC or FRP? Predrill if cracking is a concern.



__________________
kok328 is offline  
 
Reply With Quote Quick reply to this message
Old 04-04-2012, 05:35 PM  
cmerk16
Junior Member
 
Join Date: Mar 2012
Posts: 10
Default

PVC. U can't predrill if you are using a trim gun. What are you suggesting by predrilling?

__________________
cmerk16 is offline  
 
Reply With Quote Quick reply to this message
Old 04-04-2012, 06:06 PM  
nealtw
Contractor
 
Join Date: Nov 2010
Location: vancouver, b.c.
Posts: 10,273
Liked 849 Times on 758 Posts
Likes Given: 1465

Default

This should be vented soffet, no mainantence and better yet no rot do to no venting.

__________________
nealtw is offline  
 
Reply With Quote Quick reply to this message
Old 04-04-2012, 06:37 PM  
oldognewtrick
Moderator
HRT_MODERATOR.png
 
oldognewtrick's Avatar
 
Join Date: Jul 2009
Location: Nashville, TN
Posts: 5,424
Liked 459 Times on 382 Posts
Likes Given: 146

Default

Not trying to second guess, but why do you want to use sheet material? You say you want to use a trim gun, how will you cover exposed the nail heads? I'd suggest using vented soffit material or the same material you use on the side wall. Just my

__________________
oldognewtrick is offline  
 
Reply With Quote Quick reply to this message
Old 04-04-2012, 07:40 PM  
cmerk16
Junior Member
 
Join Date: Mar 2012
Posts: 10
Default

I want a clean look. When using a trim gum the nail heads sit below the surface so I would puddy over the heads. I'm using PVC do there are no worries of rot.

__________________
cmerk16 is offline  
 
Reply With Quote Quick reply to this message
Old 04-04-2012, 08:34 PM  
nealtw
Contractor
 
Join Date: Nov 2010
Location: vancouver, b.c.
Posts: 10,273
Liked 849 Times on 758 Posts
Likes Given: 1465

Default

The rot will be caused by using a solid surface and trapping moisture inside. If this construction is with permits, ask advice of inspectors before sealing this up, and if it is without permits, get some good advice.

__________________
nealtw is offline  
 
Reply With Quote Quick reply to this message
Old 04-05-2012, 01:00 AM  
oldognewtrick
Moderator
HRT_MODERATOR.png
 
oldognewtrick's Avatar
 
Join Date: Jul 2009
Location: Nashville, TN
Posts: 5,424
Liked 459 Times on 382 Posts
Likes Given: 146

Default

We're not worried about rot to the surface material, our concern is the substructure you are sealing up.

__________________
oldognewtrick is offline  
 
Reply With Quote Quick reply to this message
Old 04-05-2012, 09:13 AM  
joecaption
Senior Member
 
Join Date: Jan 2011
Location: Hartfield VA, VA
Posts: 1,361
Liked 38 Times on 33 Posts
Likes Given: 2

Default

I'd be using beaded hidden vent soffit material up there. It would look so much better then a flat sheet.
If you did go with PVC sheet I would be using 1/2 thick attaching on the outsides and around where the light goes with screws then add some form of crown or cove moulding to cover the screw holes.



__________________
joecaption is offline  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Bad Install?? mdbaggs Flooring 4 03-23-2012 06:51 PM
How would I replace ceiling tiles with drywall on a ceiling that has no studs? weedelf Walls and Ceilings 2 02-24-2011 06:58 AM
Hardwood floor install above plaster ceiling dawnn Flooring 2 06-24-2007 11:17 AM
Tin Ceiling Install Dilemma taydeedee Flooring 2 08-13-2006 05:49 PM
fake stome sheets for exposed foundation horsegoer General Home Improvement Discussion 1 04-30-2006 10:20 AM