DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Walls and Ceilings > What's the best way to layout the sheetrock?




Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old 01-13-2013, 09:55 AM  
LIDIYer
Junior Member
 
Join Date: Jan 2013
Posts: 1
Default What's the best way to layout the sheetrock?

I'm re-sheetrocking a ceiling 19.5'X12.5'. The joists run the short distance (12.5'). What size sheetrock and what's the best way to lay it to minimize seams and give it the best finish?

Thanks
Joe



__________________
LIDIYer is offline  
 
Reply With Quote Quick reply to this message
Old 01-13-2013, 10:24 AM  
Wuzzat?
Senior Member
 
Wuzzat?'s Avatar
 
Join Date: Jan 2010
Posts: 2,306
Liked 165 Times on 152 Posts
Likes Given: 91

Default

With 4x8 sheets and not counting the seams at the walls, I get
sheet long side parallel to joists, 82' of seam and
sheet short side parallel to joists, 96' of seam.

But you will have to add wood to support the seams, possibly regardless of sheet orientation and joist spacing because
19.5' x 12" or 12.5' x 12"
divided by
16" or 24" O.C.
do not equal integers.

Writing a computer program to search for the minimum seam length is probably within the capabilities of an undergraduate Computer Science student.
With drawings you can do it on Excel.

You want 4x12 seam lengths?

Minimum waste/minimum cost is another issue. Draw it out, you'll see.



__________________

Last edited by Wuzzat?; 01-13-2013 at 10:57 AM.
Wuzzat? is offline  
 
Reply With Quote Quick reply to this message
Old 01-13-2013, 09:34 PM  
nealtw
Contractor
 
Join Date: Nov 2010
Location: vancouver, b.c.
Posts: 9,465
Liked 748 Times on 668 Posts
Likes Given: 1306

Default

If the joists are 24" on center you need 5/8 drywall. Depending on how the joists are in the space, you might start with an 8ft and 12ft then a 10ft and 10 ft then 12 ft and 8 ft. And another 10 ft sheet for the two peices you need to finsh with. If the joist don't land in your faver you may have to add to the length of some sheets. In some areas you can by drywall that is 54 inches wide, if you used that for one run you would save one line of filler.

__________________
nealtw is offline  
 
Reply With Quote Quick reply to this message
Old 01-14-2013, 06:17 AM  
Wuzzat?
Senior Member
 
Wuzzat?'s Avatar
 
Join Date: Jan 2010
Posts: 2,306
Liked 165 Times on 152 Posts
Likes Given: 91

Default

Since 19.5 x 12.5 = 243.75 the minimum number of sheets are
4x8, 243.75/32= 8 and 4x12, 6
but you'd have splices everywhere.

If you make a 1' : 1/8" scale drawing of the 19.5 room and cut out pieces of paper scaled to the sheet sizes, you can try combos pretty fast. There are many many combinations/permutations but you have a good chance of finding some minimums.

I don't know how fast you can tape seams but an hour spent at the drawing board will probably be worth it. Take several configs with you to the store in case they don't have all the sizes you need in stock. Record each config and the sheets necessary to do it so you don't have to search over again when you get home with the drywall.

__________________

Last edited by Wuzzat?; 01-14-2013 at 06:44 AM.
Wuzzat? is offline  
 
Reply With Quote Quick reply to this message
Old 01-14-2013, 03:04 PM  
drewdin
Junior Member
 
Join Date: Aug 2012
Posts: 391
Liked 25 Times on 22 Posts
Likes Given: 78

Default

I was going to recommend autocad, thats what I use for everything. I did a quick sketch, this is not how you would lay out the boards. Its just a start for how many boards (10) and the rough lengths they would need to be cut. Plus, using 12.5 as stud spacing does not seem correct. I would have to see it to draw it correctly.



latout.jpg  
__________________

Last edited by drewdin; 01-14-2013 at 03:07 PM.
drewdin is offline  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
basement layout mason82 General Home Improvement Discussion 3 10-25-2011 05:00 PM
kitchen layout blackandgold8 General Home Improvement Discussion 1 07-09-2010 09:29 AM
Bathroom layout help JoePikePark Decorating and Design 2 01-10-2010 11:02 PM
Estimate / Layout software speedy1906 General Home Improvement Discussion 2 12-11-2007 01:24 PM
3d Kitchen Layout Software TxBuilder General Home Improvement Discussion 2 03-27-2006 09:12 PM