DIY Home Improvement, Remodeling & Repair Forum > Appliances > General Appliance Discussion > Clothes Washer problem




Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old 01-18-2014, 06:53 AM  
jsteam
Junior Member
 
Join Date: Jan 2014
Posts: 5
Liked 1 Times on 1 Posts

Default Clothes Washer problem

I have an older whirlpool clothes washer, the coupler between the motor and transmission broke into pieces and the washer wouldn't spin. I ordered another replacement coupler and replacing that wasn't much of a problem, the disassembly however was not so easy and I had to take the outer shell off of the drum because the motor face the wall of the housing making it impossible to remove the motor a bit to replace the coupler, ok so I assemble everything back in the order that I had removed it primarily wiring to take stress of the housing removal , now It won't fill water or nothing happens at all when I turn the dial for wash spin etc. I suspected lack of ground so I repeatedly tried to fasten the ground wire in better support and location with no results I also tired different working outlets to make sure power was going to the washer, don't know what I am overlooking or what I did to make the washer do nothing, need advise on what I could do to troubleshoot and repair this,Thanks.



__________________

Last edited by jsteam; 01-18-2014 at 07:00 AM.
jsteam is offline  
 
Reply With Quote Quick reply to this message
Old 01-18-2014, 07:11 AM  
woodchuck
Senior Member
 
Join Date: Jul 2008
Location: Tuscaloosa, Al
Posts: 244
Liked 15 Times on 14 Posts

Default

Could(should) be as simple as a wire coming unplugged on the washer control with all the movement during repair. Check everywhere carefully with a flashlight.



__________________
woodchuck is offline  
 
Reply With Quote Quick reply to this message
Old 01-18-2014, 07:30 AM  
inspectorD
Housebroken
HRT_MODERATOR.png
 
inspectorD's Avatar
 
Join Date: Dec 2005
Location: Litchfield, CT
Posts: 3,935
Liked 96 Times on 82 Posts
Likes Given: 189

Default yup

Make sure the door button is working also, then check to make sure the timer connections are all tight, which I am sure you already tried.
Is it possible the timer went bad and the piece broke at the same time, or caused it to by running too long?
Just spitballin here..

__________________

Just My
Made in the

inspectorD is offline  
 
Reply With Quote Quick reply to this message
Old 01-18-2014, 08:42 AM  
jsteam
Junior Member
 
Join Date: Jan 2014
Posts: 5
Liked 1 Times on 1 Posts

Default

Actually it turned out that a white wire was broken on the power cord It was down farther into the back where I didn't spot it at first,Thanks for the helpful suggestions guys!

__________________
jsteam is offline  
inspectorD Likes This 
Reply With Quote Quick reply to this message
Old 01-18-2014, 08:51 AM  
Wuzzat?
Senior Member
 
Wuzzat?'s Avatar
 
Join Date: Jan 2010
Posts: 2,220
Liked 150 Times on 137 Posts
Likes Given: 80

Default

Yes, completely dead usually means some one thing very basic is wrong (because it's unlikely more than one thing will fail over a short span of time, unless you accidentally put 240vac into this machine).



__________________
Wuzzat? is online now  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Dryer wont dry clothes newtda General Appliance Discussion 8 07-27-2011 06:12 PM
Dryer taking forever to dry clothes jrsharp21 General Appliance Discussion 19 03-26-2009 09:44 AM
Clothes Gas Dryer not heating oadsouza General Appliance Discussion 2 03-18-2008 11:34 AM