DIY Home Improvement, Remodeling & Repair Forum > Appliances > Water Softener and Heater > Thermcouper




Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old 09-03-2012, 09:00 PM  
jabpp4
Junior Member
 
Join Date: Sep 2012
Posts: 1
Default Thermcouper

How often should a thermocoupler be replace on a hot,water tank? We have replaced ours about 4-5 times in 4 yrs. Is something wrong? Our house is new, 4 yrs old.



__________________
jabpp4 is offline  
 
Reply With Quote Quick reply to this message
Old 09-04-2012, 03:50 PM  
kok328
Supporting Member
HRT_SUPPORTER.png
 
Join Date: Nov 2007
Location: Grand Blanc, MI
Posts: 2,147
Liked 94 Times on 83 Posts
Likes Given: 60

Default

Not sure what the problem could be but, 4-5 times in 4 yrs is excessive



__________________
kok328 is offline  
 
Reply With Quote Quick reply to this message
Old 09-04-2012, 08:14 PM  
Blue Jay
Senior Member
 
Blue Jay's Avatar
 
Join Date: Jun 2008
Location: La Rue, Ohio
Posts: 248
Liked 10 Times on 10 Posts
Likes Given: 11

Default

Possible the pilot may be too high and burning it up?

__________________
Blue Jay is offline  
 
Reply With Quote Quick reply to this message
Old 10-17-2012, 08:23 AM  
notmrjohn
Obnoxious Knowitalll
 
notmrjohn's Avatar
 
Join Date: Sep 2012
Posts: 251
Liked 24 Times on 23 Posts
Likes Given: 12

Default

If only 4 years old, your thermocouple probably has a diode attached to it, that may be part that is actually being damaged.
. Not enough air flowing through the combustion chamber to carry the heat up through the flue causes heat build up, which kills the thermocouple. Make sure exhaust flue is large enough, not leaking, unobstructed inside, and runs in as straight and short route thru roof as possible and extends above roof far enough. Also make sure plenty of air is getting to unit to increase air flow, could be plenty of air to keep it burning but not enough to keep thermocouple cool. Larger or another opening into heater compartment, opening should be as low as possible.

Have all your replacements been same brand? Another brand may be more rugged and dependable.

__________________

[CENTER][FONT=Comic Sans MS]Measure twice, cut once.[/FONT][/CENTER]
[CENTER][FONT=Comic Sans MS]Look at the nail, not the hammer. Watch the fence, not the blade.[/FONT][/CENTER]
[CENTER][FONT=Comic Sans MS]If you hook your thumb over your belt you won't hit it with the hammer or leave it layin on the saw table.[/FONT][/CENTER]

notmrjohn is offline  
 
Reply With Quote Quick reply to this message
Old 10-17-2012, 03:22 PM  
Wuzzat?
Senior Member
 
Wuzzat?'s Avatar
 
Join Date: Jan 2010
Posts: 2,206
Liked 146 Times on 133 Posts
Likes Given: 80

Default

Sounds like they are being severely abused by some as yet unfound root cause.

Measure the voltage output of your thermocouples to check what temps. they are seeing. Common voltages are 25 mV up to 750 mV and when they are turning on a gas valve the voltages may drop to half.

also check the current flow. (Edit: this is nearly impossible without special equipment).

As circuits go this cannot be much simpler.



__________________

Last edited by Wuzzat?; 10-18-2012 at 02:15 PM.
Wuzzat? is offline  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On