DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Cleaning > Mold keeps coming back




Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old 03-16-2011, 09:27 AM  
bobtheblindguy
Member
 
Join Date: Dec 2009
Posts: 37
Default Mold keeps coming back

Last year when I pulled out our dresser to clean I noticed some mold in the corner. I clean it using a solution of bleach and water. Then this year ( year once a year) it returned. This is an outside corner so I'am thinking it's not insulated enough. Any suggestions on how to stop this mold from re-occuring.



__________________

BobTheBlindGuy.com

bobtheblindguy is offline  
 
Reply With Quote Quick reply to this message
Old 03-17-2011, 06:45 AM  
kok328
Supporting Member
HRT_SUPPORTER.png
 
Join Date: Nov 2007
Location: Grand Blanc, MI
Posts: 2,196
Liked 112 Times on 97 Posts
Likes Given: 64

Default

I've had the same problem but, moved from the house before discovering a solution.
You may have a roof or plumbing leak that is feeding the mold. I was also told that there was not enough air circulation and that also will cause the mold to regrow after cleaning with bleach. Come to find out, cleaning with bleach is how to remove it. Spray the effected area with vinegar to keep it from returning. If it does come back then the problem is most likely inside the wall and to kill the source you will have to open up the wall.



__________________
kok328 is offline  
 
Reply With Quote Quick reply to this message
Old 03-17-2011, 12:52 PM  
joecaption
Senior Member
 
Join Date: Jan 2011
Location: Hartfield VA, VA
Posts: 1,361
Liked 38 Times on 33 Posts
Likes Given: 2

Default

Air leaking in around window causing a cold spot causing moist air in the room to condence.
Needing replacement widows,
Lack of insulation in the wall.
No ridge vent on the roof, no soffit vents, or there blocked up with insulation because no one installed foam baffles before insulating.
Someone left the foundation vents open again, best thing to do is knock them out and install automatic open ones.
If you have central heating and air, no 1" gap under the door for return air flow.

__________________
joecaption is offline  
 
Reply With Quote Quick reply to this message
Old 03-26-2011, 05:38 AM  
itsreallyconc
Senior Member
 
Join Date: Sep 2009
Location: hilton head & atl, sc & ga
Posts: 287
Liked 1 Times on 1 Posts

Default

that's the ticket - there's always a silver bullet inside a plastic bottle so fix the result & ignore the cause,,, now you know why we buy so little from apron/vest stores,,, have stood in different areas many times & heard the exact opposite of good advice being given to customers,,, bleach is still the cheapest & best solution to kill mold/mildew but nothing will work UNLESS you address the cause.

itsreallyconc - atlanta ( marietta )

' exterild regress ' ? ? ? when technical ' training ' improves, credibility will be enhanced,,, the cost of tech training is NOT a budget item for the apron stores - they serve HOMEOWNERS,,, pro's needing tech stuff buy from specialty const supply houses,,, jacklegs use apron stores,,, yes, this can be perceived as a rant but its my own opinion along w/many other caring pro's,,, we make good profits by repairing h/o's attempts based on what they were told by the ' apron pro '
__________________
itsreallyconc is offline  
 
Reply With Quote Quick reply to this message
Old 03-28-2011, 08:16 AM  
DIYMom
Junior Member
 
Join Date: Mar 2011
Location: Madison, WI
Posts: 21
Liked 1 Times on 1 Posts

Default

I agree that you need to make sure of the cause. Our neighbors just went through this! Turns out they had a small crack in the foundation & when they ripped up the carpet they found tons of mold. They brought in the pros to test the mold. Anyway, big mess. My husband has been helping them drywall since they had to even rip out walls.
They had inklings of an issue years ago but didn't follow up.

__________________
DIYMom is offline  
 
Reply With Quote Quick reply to this message
Old 03-28-2011, 04:29 PM  
itsreallyconc
Senior Member
 
Join Date: Sep 2009
Location: hilton head & atl, sc & ga
Posts: 287
Liked 1 Times on 1 Posts

Default

just looked at a job this afternoon - water leaking into a bsmt bedroom thru the foundation - to resolve it they had the landscaper regrade w/more dirt outside & install a 4" drain pipe which has helped a lot EXCEPT they still get water < HUH ? >,,, the drainage pipe doesn't drain anywhere < evidently his landscaper doesn't know it takes a downhill for wtr to drain ! >

husband said they'll get by for a while & they can ' handle ' the leaking wtr so i just shook my head & left ! ! ! their drywall contractor's replacing the drywall tomorrow that was ruined by the leaking wtr,,, told him he'll have more work there when it rains again
__________________
itsreallyconc is offline  
 
Reply With Quote Quick reply to this message
Old 03-30-2011, 01:54 PM  
Perry525
Senior Member
 
Perry525's Avatar
 
Join Date: Apr 2010
Location: Lake Wales, Fl.
Posts: 112
Liked 11 Times on 7 Posts

Default

Mould is caused by water vapor in the air!
You cook, wash, dry things indoors, breath, sweat.....all these things create water vapour in the home.
Water vapour is programmed by nature to condense on the nearest cold surface.
You see water vapour as condensation on cold mirrors and windows.
You do not see mould on anything that is warm!
You often get condensation on windows overnight after closing the blinds or curtains, this is because you have closed off the warm air that keeps the windows dry during the day.
Move the dresser away from the wall to enable the air to circulate behind it.
If you turn the heating down or off at any time. Stop doing it!
Warm air can hold a certain amount of water vapour at a given temperature, when you turn the heating down or off, the air temperature drops, it can no longer hold the same amount of water vapour, so the water vapour heads for the cold patch behind your dresser.

__________________

Last edited by Perry525; 03-30-2011 at 01:56 PM.
Perry525 is offline  
 
Reply With Quote Quick reply to this message
Old 04-09-2011, 10:05 AM  
mkklein68
Junior Member
 
Join Date: Jul 2010
Posts: 4
Liked 1 Times on 1 Posts
Likes Given: 1

Default Mold keeps coming back

In reading responses to the original question, I see a lot of misconceptions going on here. Mold generally needs three things to grow: food source, spores and moisture. The first two are everywhere because they are floating around in the air. Therefore, moisture is usually the issue that needs resolving. When we at Criterium-Cincinnati Engineers investigate mold growth issues, we are usually looking for the moisture source(s).

The moisture source could be due to many reasons, including some cited in the replies. But, the only way to really know the source is to have the issue investigated by a knowledgeable investigator. That being said, I will venture a couple of possibilities for the original mold growth. I doubt that the issue is a foundation leak if the location is above the foundation. Water usually travels downward--not up, unless it is wicking up in the materials, which usually takes a bit of water and the mold growth would be relatively heavy. If the found mold growth is on the lighter side, I am guessing that it is due to condensation because of its location behind the dresser. I have seen cases like this before. Mold likes dark, low-air movement areas in which to grow--just add water.

Mold can be cleaned up using bleach water or one of the cleaning products sold as being a mildewicide or fungicide (mildew IS mold IS microfungi, BTW). Be sure to follow the label directions. Also be aware, all "icides" need a certain amount of time in contact with the substance that is being killed to be effective, and that amount of time is usually around 10 minutes, assuming that it fully penetrates the stuff. To help penetration, you might want to add a few drops of a dishwashing liquid--my fave is Dawn (and not because P&G is located here). I also like Murphy's Oil Soap made up to be a little more concentrated than normal because it tends to coat the mold and keep it from getting airborne during cleaning.

However, if you do not eliminate the moisture source, the mold growth is likely to keep coming back. To prevent its regrowth, you might be able to relocate the dresser so the area is exposed to air movement to evaporate the moisture. Otherwise, you will need to take more aggressive measures to eliminate the moisture, such as better insulation.

However, you have to wonder, what is the source of the water in the home that is condensing in the area. A lot of water is generated in the home by cooking, bathing, people, etc. Many homes have these sources without condensation; so why is condensation occurring here? Sometimes, the issue can be more insidious, such as water pooling up the home. That is where the pros come in.

Note that I have focused on condensation as the moisture source causing the growth. Other moisture issues can definitely be at fault, such as water not weeping properly from brick veneer, leaks around windows or even from roofs, etc. I once investigated a leak that occurred on the second story but only showed up in the basement. Again, that is where the pros come in.

Hope this info helps.

__________________
mkklein68 is offline  
 
Reply With Quote Quick reply to this message
Old 04-13-2011, 08:31 PM  
RangerRick
Junior Member
 
Join Date: Mar 2011
Location: DeForest, WI
Posts: 6
Default

That's helpful Matt. I've wondered about when should you bring in the pros.

__________________
RangerRick is offline  
 
Reply With Quote Quick reply to this message
Old 04-18-2011, 02:08 PM  
CMHbob
Veteran Rehabber
 
Join Date: Apr 2011
Location: columbus, ohio
Posts: 17
Default Eliminating Mold

We found mold in one unit of our 50-unit condo building last year. We hired a professional to identify and remediate the problem. We were told by this company that bleach causes more health issues than mold, plus it only cleans the surface. Strong soap and water is 99% effective as bleach with no health problems. He referred us to EPA Guidelines
Method 1: Wet vacuum (in the case of porous materials, some mold spores/fragments will remain in the material but will not grow if the material is completely dried). Steam cleaning may be an alternative for carpets and some upholstered furniture.
Method 2: Damp-wipe surfaces with plain water or with water and detergent solution (except wood —use wood floor cleaner); scrub as needed.
Method 3: High-efficiency particulate air (HEPA) vacuum after the material has been thoroughly dried. Dispose of the contents of the HEPA vacuum in well-sealed plastic bags.
Method 4: Discard - remove water-damaged materials and seal in plastic bags while inside of containment, if present. Dispose of as normal waste. HEPA vacuum area after it is dried.

According to the pro, the only way to stop mold is to eliminate the source of moisture allowing it to grow.



__________________

[SIZE="4"][FONT="Comic Sans MS"]Bob Yorde[/FONT][/SIZE]
[I]Visit my [URL="http://budgetreno.blogspot.com/"]blog [/URL] for my latest project and reno tips![/I]

CMHbob is offline  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Christmas is coming! TxBuilder General Chit-Chat 18 12-20-2010 03:11 PM
Cold Air coming in through Air Return stefaka20 HVAC 1 12-07-2010 03:07 PM
Thanksgiving is Coming up! TxBuilder General Chit-Chat 4 11-18-2010 01:41 PM
Carpet coming up jhudson Flooring 4 02-12-2006 03:47 PM