DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Flooring > Board floor




Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old 08-05-2009, 10:30 PM  
DonM
Junior Member
 
DonM's Avatar
 
Join Date: Aug 2009
Location: Montpelier, Idaho, Idaho
Posts: 2
Default Board floor

My wife wants an old time board floor in the bedroom. I have some 1x8 cedar boards laying in the barn I think I'll use. Cost much less than buying new boards, altho I haven't seen a cedar floor before.

These boards do not have tongue and groove. She wants the nails to show. Should I glue the boards down to the subfloor as I nail them down? I think I'll put the rough side down (the side made to face out for siding) and the plain smooth side up for easier sanding.

I have a belt sander and a Random Orbital sander. If I use these tools to sand the floor, Is it going to take me days instead of the hours it would take if I go rent a professional floor sander?

Thanks
DonM



__________________
DonM is offline  
 
Reply With Quote Quick reply to this message
Old 08-05-2009, 11:54 PM  
Nestor_Kelebay
Emperor Penguin
 
Nestor_Kelebay's Avatar
 
Join Date: Mar 2009
Location: Winnipeg, Manitoba
Posts: 1,844
Liked 2 Times on 2 Posts

Default

Don:

The reason you haven't seen a cedar wood floor before is because cedar is way too soft to make for a durable floor. It's so soft that it's the only wood (that I know of) that you can leave a mark in using just your fingernail.

So, you can expect to leave permanent marks on your floor if you drag furniture across it, or probably even move your bed to clean under it.

Years ago, when it was common to have hardwood floors, people would often only use hardwoods like maple and oak on the the main floor of their house; where the living room and dining room were located and where all the entertaining of guests took place. On the upper floors, where all the bedrooms were, they would often opt for fir flooring to save money. After all, people typically wore socks inside the house and went barefoot at night, so the wood on the floor didn't have to be hard to stand up to dirt being ground into it's surface underfoot. So, I'd say the softest wood you could reasonably go with in a bedroom would be fir.

Cedar is an attractive wood because much of the cedar we see is clear (no knots, or only small knots). So, it looks like it would make for a beautiful floor, and it would probably initially look great. The problem is that cedar is such a soft wood, that floor would be very easily damaged from scratches and dents, and it wouldn't look good for long.

It'd be like using ordinary latex wall paint to paint a floor. The paint would be so soft that dirt would get embedded in it underfoot, and the traffic lanes would start showing as dirty areas on the floor before you knew it. And, even though the floor would look dirty, you wouldn't be able to remove the embedded dirt without also removing the paint, so ordinary sweeping or mopping would be ineffective. The only way to clean the floor would be to scrub the dirty surface layer off. Basically, it would simply be a very poor choice for a floor covering. You'd get similar results using a very soft wood like cedar on a working surface like a floor. Anything you dropped on that floor would leave a dent, anything you dragged across it would leave a scratch, and you couldn't walk on it with shoes because that would cause dirt to be embedded in the soft wood. And, a hefty woman in high heels would wreck that floor.



__________________

Last edited by Nestor_Kelebay; 08-06-2009 at 12:07 AM.
Nestor_Kelebay is offline  
 
Reply With Quote Quick reply to this message
Old 08-06-2009, 08:13 AM  
kok328
Supporting Member
HRT_SUPPORTER.png
 
Join Date: Nov 2007
Location: Grand Blanc, MI
Posts: 2,185
Liked 105 Times on 92 Posts
Likes Given: 61

Default

Also, cedar will bleed it's pigments and turn your shoes and socks a red color.
A better application for the cedar would be for the walls of your closets. Moths don't like cedar but, they love clothing.

__________________
kok328 is offline  
 
Reply With Quote Quick reply to this message
Old 08-06-2009, 09:28 AM  
DonM
Junior Member
 
DonM's Avatar
 
Join Date: Aug 2009
Location: Montpelier, Idaho, Idaho
Posts: 2
Default

Thanks for the heads up on the use of cedar. Maybe I'll use some of it for wanscot and paint it. Maybe it'll stay stacked in the barn.

I guess I'll go spend the $300 bucks for pine and call it money saved in the long run. I won't have to go back in and pull out the cedar floor and start again..

Don

__________________
DonM is offline  
 
Reply With Quote Quick reply to this message
Old 08-06-2009, 04:45 PM  
tmhremodel
Junior Member
 
Join Date: Jul 2009
Posts: 20
Default

cedar flooring would also come apart as you walk on it etc. as a soft wood it amazingly enough "snaps" apart.



__________________
tmhremodel is offline  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Jumping on board HouseRepairTalk railer Introductions 1 01-30-2009 06:01 PM
New to the board Barry M Introductions 1 09-30-2007 07:51 PM
Making a light board ( basicly like a sound board) for studio colepittman Electrical and Wiring 0 08-04-2007 02:27 PM
Deck Board Gap cibula11 General Home Improvement Discussion 3 06-24-2007 11:26 AM
Board Span question texastom Introductions 2 07-15-2006 06:06 AM