DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Flooring > Distance between stringers





Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old 01-14-2008, 09:38 PM  
Outbacker
Member
 
Join Date: Feb 2006
Posts: 62
Default Distance between stringers

I am looking at putting in a step from my family room to the hallway which is perpendicular to the room. It is exactly 14 inches up from the family room floor to the hallway floor. I want to put in 2 metal stringers with a 1 inch thick step board. Problem is most of the stringers that I have seen have a vertical piece at the top of them that bolts to the wall, and that is fine as long as I can set them (the stringers) far enough apart to meet the door frame which is 36 inches. My concern is the step board will start to sag after a while, or will it? Am I okay with this distance between the stringers and not have the step sag? I am also thinking that I may bolt (or weld) a small "L" bracket in under the step between the stringers for support. What do you think?



__________________
Outbacker is offline  
 
Reply With Quote Quick reply to this message
Old 01-14-2008, 10:49 PM  
guyod
Senior Member
 
Join Date: Jan 2008
Location: Wind Gap, PA
Posts: 418
Liked 19 Times on 18 Posts
Likes Given: 8

Default

You are right. a 36" span is way too far. But since its only one step you can get away with if you use a riser and mount a 1x3 board to the wall so that the back of the stair thread sits on it and the front of the step sits on the riser. Use oak and it will hold a ton.



__________________
guyod is offline  
 
Reply With Quote Quick reply to this message
Old 01-14-2008, 11:38 PM  
ToolGuy
Senior Member
 
ToolGuy's Avatar
 
Join Date: Nov 2007
Posts: 482
Default

I'm trying to picture this and not sure why you need a stringer at all. If it's just one step just build it like a box. whatever the case, a 1" (5/4 stock) or especially a 1x (3/4" thick) will definately need support midway.

__________________

[COLOR="DarkRed"][B]~ ToolGuy ~[/B][/COLOR]

[I]Save money on tools at [URL="http://mytoolbox.net"]MyToolbox.net[/URL]
[/I]

ToolGuy is offline  
 
Reply With Quote Quick reply to this message
Old 01-15-2008, 12:01 PM  
glennjanie
Senior Member
 
Join Date: Mar 2006
Posts: 2,992
Liked 2 Times on 2 Posts

Send a message via AIM to glennjanie
Default

Hello Outbacker:
ToolGuy is correct; you only need a box step 7" tall, you step on that and then on the upper floor. The box could be 4' wide if you want to cover the door, comfortably. Build the rectangle 6 1/4" tall, screw the back board to the wall and add the tread on top of the box. You could even round the ends of the tread to make it look a little neater. The tread should be made of a 1 X 12 board and make the box an inch less than the width ( front to back )of the tread.
Glenn

__________________
glennjanie is offline  
 
Reply With Quote Quick reply to this message
Old 01-15-2008, 05:00 PM  
guyod
Senior Member
 
Join Date: Jan 2008
Location: Wind Gap, PA
Posts: 418
Liked 19 Times on 18 Posts
Likes Given: 8

Default

I would of said to make a box too but he seemed pretty set on using a metal stringer

__________________
guyod is offline  
 
Reply With Quote Quick reply to this message
Old 01-15-2008, 10:38 PM  
Outbacker
Member
 
Join Date: Feb 2006
Posts: 62
Default

Thanks for the replies. Right now there is a box step in place, and I just want a new look with the metal stringers and a nicely stained oak step. I will most likely take the two stringers to a welding place and have them weld a "L" bracket between them and this will support the step. Thanks again for the help.

__________________
Outbacker is offline  
 
Reply With Quote Quick reply to this message
Old 01-16-2008, 06:50 AM  
guyod
Senior Member
 
Join Date: Jan 2008
Location: Wind Gap, PA
Posts: 418
Liked 19 Times on 18 Posts
Likes Given: 8

Default

Sounds like you dont want a riser (perpindictular board on back of step)
so you can see the metal stringer right? even if you do weld a bracket in to make it strong enough. It is still not going to look strong enough. People will look at your step and wonder if its going to hold them and not how nice the oak stained thread looks. I would find a stringer without the tab on top or have your welder take it off and relocated it to the side or bottom. Then keep them under 24" on center.

__________________
guyod is offline  
 
Reply With Quote Quick reply to this message
Old 01-16-2008, 09:07 AM  
glennjanie
Senior Member
 
Join Date: Mar 2006
Posts: 2,992
Liked 2 Times on 2 Posts

Send a message via AIM to glennjanie
Default

If you want the look of the steel stringers just use 1 1/2" stock for the treads. Oak and Southern Yellow Pine have the same bending rating; you could even use treated lumber. I use 2 X 12 stair treads on all my decks and, yes they are 36" long.
Glenn



__________________
glennjanie is offline  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On