DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Flooring > Insulating Basement Walls???




Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old 05-19-2006, 08:14 AM  
pmfinnegan2
Junior Member
 
Join Date: May 2006
Posts: 1
Default Insulating Basement Walls???

I am going to be finishing my basement interior. Along the poured concrete basement walls I am going to putting up studs. When I insulate in between them do I just use regular fiberglass isulation, or do I have to use something special because it is along concrete walls?



__________________
pmfinnegan2 is offline  
 
Reply With Quote Quick reply to this message
Old 05-19-2006, 03:08 PM  
Square Eye
Senior Member
 
Square Eye's Avatar
 
Join Date: Jan 2006
Posts: 1,273
Liked 4 Times on 4 Posts

Default

Foam board is by far the preferred insulation in an area that could possibly see moisture. Fiberglass will absorb moisture and hold it in a non-ventilated environment for an unbelievable amount of time. Meanwhile, mold and rot will set in and work it's majic on the surrounding wood and wall board. Foam, well, closed cell styrofoam, will not hold moisture. It comes in blue, white, green and pink depending on where you buy it. The old style foil faced foam board will evetually absorb water, but the newer stuff will not. There is another thread on this subject. I'll post a link as soon as I find it.



__________________

[URL="http://www.houserepairtalk.com/announcement.php?f=39&a=6"][size=3]The Ten Commandments of House Repair Talk[/size][/URL]



[URL="http://home.bellsouth.net/p/s/community.dll?ep=16&groupid=289528&ck="]Square Eye's home page[/URL]

Square Eye is offline  
 
Reply With Quote Quick reply to this message
Old 05-19-2006, 03:15 PM  
Square Eye
Senior Member
 
Square Eye's Avatar
 
Join Date: Jan 2006
Posts: 1,273
Liked 4 Times on 4 Posts

Default

http://www.houserepairtalk.com/showthread.php?t=629

Similar situation.
__________________

[URL="http://www.houserepairtalk.com/announcement.php?f=39&a=6"][size=3]The Ten Commandments of House Repair Talk[/size][/URL]



[URL="http://home.bellsouth.net/p/s/community.dll?ep=16&groupid=289528&ck="]Square Eye's home page[/URL]

Square Eye is offline  
 
Reply With Quote Quick reply to this message
Old 05-19-2006, 03:53 PM  
woodworkingmenace
Senior Member
 
Join Date: Apr 2006
Posts: 112
Send a message via MSN to woodworkingmenace
Default

Ok, first off, you make your sill plate (bottom of your wall), out of treated lumber. Then use regular pine for the uprights.

Now, keep the wood approximately 1/2 inch from the wall, (unless you use treated lumber for this also). I would go with the pink corning fiberglass R-13 insulation for the walls, if you have the room after you mark off the wall area.

Put a chalk mark down, for the wood, and the 1/2 inch so that you will see just how much room you will have left...Especially if your going to do all four walls this way...Those 2X4s take up some space! (Figuring that all four walls are poured, though, they may not be..so, its just my assumption).

Drop ceiling on the top, so you can get to the plumbing and electrical wiring if needed be.

For the basement floor, put 4 mil plastic on the ground.. a 12" X 12" square and duct tape it down for 24 hours to see if you get moisture wicking up from the concrete. (do this when you have some good rains, or a few days of rain, to be sure), and if not, then put indoor, out door carpeting or basically any type of carpeting with a foam backer padding.

Of course, you could be "safe", and put sleepers down, 1X2s and space every 8" and put plywood over that, to be sure (again, make sure its treated lumber), and cut the lumber outside in the air, or plenty of ventilation from the copper sulfate, (you dont want to breathe this stuff in your lungs).

Ok, my diatribe is over for this thread for awhile, others will "chime in" and give better ideas, but, these are mine...

Hmmm I shouldnt of eaten supper, cause ol' square eyes (unless he is trying to immitate popeye the sailor, he shoud have two of them peepers to see with, eh?)...hmmmm ... got ahead of me...LOL!!!

Jesse

__________________
woodworkingmenace is offline  
 
Reply With Quote Quick reply to this message
Old 05-24-2006, 07:56 PM  
inspectorD
Housebroken
HRT_MODERATOR.png
 
inspectorD's Avatar
 
Join Date: Dec 2005
Location: Litchfield, CT
Posts: 4,036
Liked 119 Times on 99 Posts
Likes Given: 268

Default The best way...

I knew I would find it.....
WWW.buildingscience.com/resources/basements.htm
Always test your basement for radon before you need to tear it out to mitigate a problem
Enjoy your basement.



__________________

Just My
Made in the


Last edited by inspectorD; 05-24-2006 at 07:58 PM.
inspectorD is offline  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
question on resurfacing brick basement walls barleypopmaker Bricks, Masonry and Concrete 6 01-02-2008 05:15 PM
Insulating Closed Walls rp14 HVAC 5 11-06-2007 08:25 AM
basement walls MarcusCarcus71 Bricks, Masonry and Concrete 1 10-01-2006 07:09 AM
Basement insulating help needed. Model Builder General Home Improvement Discussion 12 04-15-2006 06:04 PM
Insulating Exterior Walls broke Insulation and Radiant Barriers 8 04-06-2006 10:02 PM