DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Flooring > Patching sub-floor cement board




Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old 08-05-2012, 05:25 PM  
Kradak
Junior Member
 
Kradak's Avatar
 
Join Date: Jan 2011
Location: Rockville, Maryland
Posts: 6
Liked 1 Times on 1 Posts

Default Patching sub-floor cement board



My master bathroom used to have a vinyl floor and a fake modesty wall separating the shower/toilet zone from the vanity zone. My wife and I aren't as modest as when the house was built in 1965--heck, we don't even sleep in separate beds!

Anyway, I pulled up the flooring and got rid of the fake wall. I pulled up the 2x3 sole plate, leaving a gaping hole down to the wooden sub-floor.

Do you have any suggestions as to what I should do here?

(a) When tiling over, just make sure the tiles are large enough to span the gap--the tile should be strong enough
(b) Fill it up with leveling compound
(c) Fill it up with a concrete patch
(d) Screw in a 2 1/2" wide piece of durock and tape and mortar the gaps
(e) Pull up the whole floor and re-do it all, or
(f) Torch the place and start fresh with the insurance money

Thanks,

Chris


__________________
Kradak is offline  
 
Reply With Quote Quick reply to this message
Old 08-06-2012, 03:57 PM  
nealtw
Contractor
 
Join Date: Nov 2010
Location: vancouver, b.c.
Posts: 10,211
Liked 837 Times on 748 Posts
Likes Given: 1453

Default

It depends on what the second sheeting is and how flexable the floor is. You may want to remove and replace it, if it is 1/2" particle board. If it is solid I would fill it with wood and cover the whole floor with a concrete underlayment.



__________________
nealtw is online now  
 
Reply With Quote Quick reply to this message
Old 08-08-2012, 05:01 PM  
Kradak
Junior Member
 
Kradak's Avatar
 
Join Date: Jan 2011
Location: Rockville, Maryland
Posts: 6
Liked 1 Times on 1 Posts

Default

Neal,

The second sheet with the cutout shown is 1 1/2" of a 'particle board', but in this case, the particles are aggregate and the board-like material is cement...

__________________
Kradak is offline  
 
Reply With Quote Quick reply to this message
Old 08-08-2012, 05:53 PM  
nealtw
Contractor
 
Join Date: Nov 2010
Location: vancouver, b.c.
Posts: 10,211
Liked 837 Times on 748 Posts
Likes Given: 1453

Default

Sounds like a substantial floor for vinyl. I think you could do (B), (C) or (D)but waite twenty minutes, someone will correct me.

__________________
nealtw is online now  
 
Reply With Quote Quick reply to this message
Old 08-08-2012, 08:28 PM  
isola96
Senior Member
 
isola96's Avatar
 
Join Date: Oct 2011
Location: Lagrangeville, New York
Posts: 437
Liked 7 Times on 7 Posts

Default

Quote:
Originally Posted by Kradak
Neal,

The second sheet with the cutout shown is 1 1/2" of a 'particle board', but in this case, the particles are aggregate and the board-like material is cement...


You need to get down to the plywood. Particle board does not stay for tile. How much ply do you have from joists up?
__________________
isola96 is offline  
 
Reply With Quote Quick reply to this message
Old 08-08-2012, 08:42 PM  
nealtw
Contractor
 
Join Date: Nov 2010
Location: vancouver, b.c.
Posts: 10,211
Liked 837 Times on 748 Posts
Likes Given: 1453

Default

I think this room has had tile before and what he has is some sort of morter bed.

__________________
nealtw is online now  
 
Reply With Quote Quick reply to this message
Old 08-08-2012, 08:55 PM  
isola96
Senior Member
 
isola96's Avatar
 
Join Date: Oct 2011
Location: Lagrangeville, New York
Posts: 437
Liked 7 Times on 7 Posts

Default

Quote:
Originally Posted by nealtw
I think this room has had tile before and what he has is some sort of morter bed.
Oh is that what I'm seeing in the picture?
Looked like more P&S over particle board.
__________________
isola96 is offline  
 
Reply With Quote Quick reply to this message
Old 09-04-2012, 07:52 PM  
Kradak
Junior Member
 
Kradak's Avatar
 
Join Date: Jan 2011
Location: Rockville, Maryland
Posts: 6
Liked 1 Times on 1 Posts

Default

Thanks for the assist, guys. I've found an elegant solution: I sent my wife for a masonry course at the local CC and convinced her to do it: she will add a concrete patch to the holes and finish the whole floor with some leveling compound.

All I have to do then is the framing, and electrical, and lighting, and drywall, and plumbing...



__________________
Kradak is offline  
nealtw Likes This 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Hardwood floor patching with wall on top of floor sullivja Flooring 2 06-04-2012 12:07 PM
Bondo and Fiber Cement Board DependaCoat Painting Forum 3 04-13-2011 11:10 AM
Fiber Cement Board Siding broke Roofing and Siding 19 04-17-2009 06:07 PM
Floor On Pouch Needs Patching Sitting Bull Flooring 2 09-28-2008 10:31 PM
Is Cement Board REALLY necessary when Tiling? jwhdfw Flooring 6 12-05-2006 06:05 AM