DIY Home Improvement, Remodeling & Repair Forum

DIY Home Improvement, Remodeling & Repair Forum (http://www.houserepairtalk.com/forum.php)
-   Flooring (http://www.houserepairtalk.com/f13/)
-   -   Plank sub floor HELP (http://www.houserepairtalk.com/f13/plank-sub-floor-help-10181/)

y-townxj 10-20-2010 08:35 AM

Plank sub floor HELP
 
I recently pulled up the flooring in the bathroom of my house. Because I noticed there was some noticeble soft spots. There are a few planks that are rotted, so heres my question. How can I replace the rotted portions of the planks without removing the whole plank.

Heres some of the options, that are running through my mind

A. cut out the bad spots and lay down 3/4 plywood over the entire floor, just like a non plank subfloor is done.

B. cut out the bad spots, and put in new planks from joist to joist for maximum support

Any help appreciated thanks :beer:

DrHicks 10-20-2010 01:47 PM

Quote:

Originally Posted by y-townxj (Post 50085)
I recently pulled up the flooring in the bathroom of my house. Because I noticed there was some noticeble soft spots. There are a few planks that are rotted, so heres my question. How can I replace the rotted portions of the planks without removing the whole plank.

Heres some of the options, that are running through my mind

A. cut out the bad spots and lay down 3/4 plywood over the entire floor, just like a non plank subfloor is done.

B. cut out the bad spots, and put in new planks from joist to joist for maximum support

Any help appreciated thanks :beer:

I'd go "B."

You don't have to replace the entire plank. Just cut it at the nearest joists to the rotted area. Replace what you removed, secure it, and put your 3/4" plywood over the top.

It's not worth messing around with a soft floor, ESPECIALLY if you're going to install ceramic or porcelain tile.

y-townxj 10-24-2010 08:49 PM

Thanks for the info, I have a rotted spot in the corner of the room where the planks go under the wall. Should I just cut the planks off, as close to the wall as possible. Then just build out from the wall with some 2x4's so I have somthing to secure the new planks to. Sorry if this is hard to fallow any help is appreciated thanks

Jaz 10-25-2010 10:11 PM

Yes do that, you have to have blocking under the ends of all planks. May want to use something bigger than 2x4's tho. Then install new underlayment grade plywood fastened into the planks only and continue. What will you be installing? It makes a difference how you prepare the floor.

Jaz

y-townxj 10-25-2010 11:06 PM

I am unsure possibly ceramic tile

Ben8n 10-26-2010 05:11 AM

You should also take some mortar and put a layer of it down over the wooden floor and put the hardibacker over it to make sure there is no air bubbles or uneven spots in the floor. Make sure you use hardibacker screws to reason being is there is a corrisive additive to hardibacker that will eat threw drywall screws when you screw the floor down work from the center out to help push any extra mortar out from underneath. Put in mesh tape and put a thin layer of mortar over the seems then you have a prepped floor for tile. DO NOT go light on the screws either.

samfloor 10-26-2010 07:42 AM

gotogregg, Mr Home Depot guy. If they are installing ceramic, they need to know deflection. Also they need 2 layers of plywood or plank and one layer of plywood to equal at least 1 1/4 inch. And CBU adds no structural strength.


All times are GMT -6. The time now is 09:23 PM.