DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Flooring > Using Vinyl Flooring as Counter Top




Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old 07-14-2009, 01:08 PM  
luvnpeas
Junior Member
 
Join Date: Jul 2009
Posts: 8
Default Using Vinyl Flooring as Counter Top

I need to replace a kitchen sink counter top. The stock stuff won't fit. Since water is a problem (the current counter top had extensive dry rot getting into the cabinetry), I really want a splash guard in the back, and one with no seams would be great. So, what about covering plywood with vinyl, and bending the vinyl up in the back, then attaching it to the wall?

Edit: Maybe attaching a splash guard to the plywood, and the vinyl to that would be better than attaching to the wall. The basic question is just using vinyl as a counter top, and bending it.



__________________
luvnpeas is offline  
 
Reply With Quote Quick reply to this message
Old 07-14-2009, 05:21 PM  
Nestor_Kelebay
Emperor Penguin
 
Nestor_Kelebay's Avatar
 
Join Date: Mar 2009
Location: Winnipeg, Manitoba
Posts: 1,844
Liked 2 Times on 2 Posts

Default

I suppose you could do it, but it would be hard to find and adhesive with sufficient initial tack to hold the vinyl in place in the back corner. I expect the sheet vinyl will want to pull away from that corner right at the back splash. The only one I can think of would be contact cement, but the problem there would be applying the sheet vinyl so that any pattern on it was parallel with the counter top, and not having it grab until you want it to.

Normally, when dealing with contact cement you can put wax paper or wooden dowels between the mating surfaces so that you have complete control over how one surface gets bonded to another. I think you'd have a difficult time getting the sheet vinyl onto the counter in a way that looked good.

Another option would be to use an adhesive that didn't have a high initial tack, but one that would allow you to adjust the sheet vinyl a bit when you're first starting to stick it to the plywood. I'm thinking a construction adhesive or flooring adhesive that will take a few hours to set up. Then, just buy a 2X4 and clamp it in the back corner of the counter top to keep the sheet vinyl tight in the corner while the adhesive is setting up.

Can you describe your existing counter top?

If it is plastic laminate with the square corners rather than a prefab laminate top with the front bullnose and backsplash already built into it, then you are almost certain to have more success by installing a prefab plastic laminate counter top over top of what you have now.

In my case, I removed the old laminate and contact cement on my old counter tops and installed a new prefab counter top over the plywood of the old counter top. I did this in 20 or the 21 units in my small apartment building so far. If you want to see what it looks like, you can look at the pictures of the kitchens in the available suites on my website at:
http://users.usinternet.com/nkelebay/

You will need to buy a few tools to do this work, tho.

__________________

Last edited by Nestor_Kelebay; 07-14-2009 at 06:20 PM.
Nestor_Kelebay is offline  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Vinyl flooring as baseboard & tile walls new home buyer Flooring 3 05-01-2011 11:46 PM
Above counter sinks TxBuilder General Home Improvement Discussion 10 09-10-2007 11:27 AM
Removing vinyl sheet flooring WestBentley Flooring 6 03-30-2007 06:17 PM
Ceramic Tile over Vinyl flooring Kitty Flooring 29 01-09-2007 06:22 PM
kitchen counter top mrfixit Carpentry and Woodworking 7 05-13-2006 09:51 AM