DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Bricks, Masonry and Concrete > Additive for Thoroseal??




Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old 03-15-2014, 02:45 PM  
slownsteady
Supporting Member
HRT_SUPPORTER.png
 
slownsteady's Avatar
 
Join Date: Jun 2009
Location: Newton, NJ
Posts: 1,086
Liked 148 Times on 127 Posts
Likes Given: 200

Default Additive for Thoroseal??

Since the homepage on this site mentioned resin-based waterproofing, I've been wondering if there is an additive that I can add to the large bucket of Thoroseal that I already have. Any suggestions?



__________________
slownsteady is offline  
 
Reply With Quote Quick reply to this message
Old 03-16-2014, 10:59 AM  
itsreallyconc
Senior Member
 
Join Date: Sep 2009
Location: hilton head & atl, sc & ga
Posts: 287
Liked 1 Times on 1 Posts

Default

,,, in order to accomplish what end ?

john from allamuchy



__________________
itsreallyconc is offline  
 
Reply With Quote Quick reply to this message
Old 03-16-2014, 12:09 PM  
slownsteady
Supporting Member
HRT_SUPPORTER.png
 
slownsteady's Avatar
 
Join Date: Jun 2009
Location: Newton, NJ
Posts: 1,086
Liked 148 Times on 127 Posts
Likes Given: 200

Default

I want to recoat one of the interior walls in my basement. There are a few places where the first application did not stick well, despite the fact that I wire brushed the wall (pretty thoroughly, I thought) before applying it. Could be moisture or more efflorescence that I didn't get??

__________________
slownsteady is offline  
 
Reply With Quote Quick reply to this message
Old 03-16-2014, 02:48 PM  
mudmixer
Contractor
 
mudmixer's Avatar
 
Join Date: Sep 2006
Posts: 592
Liked 44 Times on 36 Posts
Likes Given: 36

Default

I think the Thoroseal instruction are to apply a second coat within 24 hours. That is pretty tough stuff and not like a paint product.

Often, an acrylic added to the Thoroseal to get some better bonding to the base material. This is when you follow the mixing instructions, including to short wait to allow the mix to absorb water and "fatten up" before the finising water addition.

One problem is that Thoroseal becomes very resistant to bonding and does not absorb much water after it is aged and even repels water quite well.

The best suggesting I have is to mist the wall just before applying the Thoroseal and use an acrylic added to the mixing water for getting the dry Thoroseal ready for application.

I think one of the additives suggested was Acryl 60 when I used it.

Thoroseal is not like a paint-type material like DryLock.

If you have some pre-mixed Thoroseal, good luck.

Dick

__________________
mudmixer is offline  
 
Reply With Quote Quick reply to this message
Old 03-16-2014, 09:13 PM  
slownsteady
Supporting Member
HRT_SUPPORTER.png
 
slownsteady's Avatar
 
Join Date: Jun 2009
Location: Newton, NJ
Posts: 1,086
Liked 148 Times on 127 Posts
Likes Given: 200

Default

Nope, it's powder. Thanks MM. I will look for that.

Should I bother trying to put on a whole second coat, or just patch the weak spots?

__________________
slownsteady is offline  
 
Reply With Quote Quick reply to this message
Old 03-16-2014, 09:15 PM  
slownsteady
Supporting Member
HRT_SUPPORTER.png
 
slownsteady's Avatar
 
Join Date: Jun 2009
Location: Newton, NJ
Posts: 1,086
Liked 148 Times on 127 Posts
Likes Given: 200

Default

itsreallyconc: here's the real question....Metro Cafe or Pub 517?

__________________
slownsteady is offline  
 
Reply With Quote Quick reply to this message
Old 03-19-2014, 10:19 AM  
slownsteady
Supporting Member
HRT_SUPPORTER.png
 
slownsteady's Avatar
 
Join Date: Jun 2009
Location: Newton, NJ
Posts: 1,086
Liked 148 Times on 127 Posts
Likes Given: 200

Default

decided to contact the Thoroseal people on this one. Here is their response:

"You can either treat just the affected areas or the entire wall, it is up to you. A surface applied bonding agent or additive to the Super Thoroseal is not necessary. The most important step is surface preparation. Make sure that any loose or unsound substrate is removed and that the surface is slightly "opened" by abrading with something such as a wire brush. Dampen the area to receive coating and apply with a stiff bristled masonry brush."



__________________
slownsteady is offline  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On