DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Bricks, Masonry and Concrete > Basement Slab Thickness Question





Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old 11-13-2012, 06:47 PM  
MoreCowbell
Member
 
Join Date: May 2011
Location: Clayton, NC
Posts: 56
Liked 1 Times on 1 Posts

Default Basement Slab Thickness Question

Those who read my other posts know that I am in the middle of a crawlspace-to-basement conversion project. A few days ago I placed the concrete for my retaining wall footing (the retaining wall is L-shaped and runs the length of two adjacent foundation walls.

I screwed up on about a 10' wide section where the footing is about an inch too high. My plan was to place a 3.5" floor slab. If I keep that same floor level, the slab will taper up to only 2.5" over that 10' section of wall footing. Here is a sketch of what I'm talking about:
Name:  Bad Footing.jpg
Views: 520
Size:  12.9 KB
My column footings have a 3.5" curb in the center where I am planning to screed my floor slab level with. I'm real nervous about tapering up to 2.5" though.

My question is would this be a real bad idea to have part of the slab go that thin? The other option I'm thinking of is to raise the finish slab surface up a 1/2" and add thickness to my column footings with a 1/2" of thinset to match the floor. That would give me a 4" slab that tapers to 3" in that section.

Any thoughts on this? Thanks.



__________________
MoreCowbell is offline  
 
Reply With Quote Quick reply to this message
Old 11-13-2012, 07:10 PM  
Wuzzat?
Senior Member
 
Wuzzat?'s Avatar
 
Join Date: Jan 2010
Posts: 1,848
Liked 95 Times on 86 Posts
Likes Given: 55

Default

Sidewalks are about 4" thk; this seems to be a minimum but maybe because of the height of a 2x4 and not so much on compressive and bending strength of the concrete.
I guess if you go thin but sure to use reinforcing wires.



__________________
Wuzzat? is offline  
 
Reply With Quote Quick reply to this message
Old 11-13-2012, 10:32 PM  
BridgeMan
Senior Member
 
BridgeMan's Avatar
 
Join Date: Aug 2011
Location: Cottage Grove, Oregon
Posts: 713
Liked 62 Times on 57 Posts

Default

Your concrete won't know it's only 2.5" thick over the footing. It will perform just fine, especially if you first chip off the top front footing corner, such that there's more of a gradual transition from the thinner to the thicker portions of the slab. Doing so eliminates the stress-raiser at the (otherwise) re-entrant corner.

__________________
BridgeMan is offline  
 
Reply With Quote Quick reply to this message
Old 11-14-2012, 06:03 PM  
MoreCowbell
Member
 
Join Date: May 2011
Location: Clayton, NC
Posts: 56
Liked 1 Times on 1 Posts

Default

Thanks for the replies. I feel better about forging ahead with my intended floor height. I'll just make sure to compact my gravel base real well and use a good amount of wire mesh reinforcement. I'll also order a higher than normal PSI mix from the concrete contractor.

__________________
MoreCowbell is offline  
 
Reply With Quote Quick reply to this message
Old 12-01-2012, 04:16 AM  
itsreallyconc
Senior Member
 
Join Date: Sep 2009
Location: hilton head & atl, sc & ga
Posts: 287
Liked 1 Times on 1 Posts

Default

paved lots of hgwy & airport conc but never understood wire mesh was good other than: 1, adding strength while the ' green ' conc was in tension ( initial set / cure ) & 2, holding the broken pieces together when it cracked all the engineer's w/whom i worked thought the same however we got paid for placing it per contract - fiber is no substitute for timely joint pattern NOR will it prevent random cracking,,, higher compressive strength makes conc more likely to resist heavier loads - if it were me, id want higher flexural strength


__________________
itsreallyconc is offline  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Basement slab even with footing? MoreCowbell Bricks, Masonry and Concrete 1 09-19-2012 05:23 PM
concrete slab thickness--southern Cal HighDesertHomeOwner Framing and Foundation 3 11-25-2010 03:35 PM
Leveling a basement slab... ToolGuy Flooring 6 07-27-2008 11:13 AM
Question about my slab. IBJammin Flooring 3 03-07-2008 05:03 PM
Question about my slab. IBJammin Framing and Foundation 1 03-06-2008 07:18 PM