DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Bricks, Masonry and Concrete > filling gaps in slab




Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old 09-25-2012, 10:41 AM  
beachguy005
Senior Member
 
Join Date: Sep 2012
Posts: 129
Liked 33 Times on 31 Posts

Default filling gaps in slab

I have a patio that's a slab on grade the had 4x8x16 block cemented on edge and used as the sill for screening. Most of the blocks are loose and I'm going to remove them to the slab.
I'm re-framing it to enclose the space and using 4x4pt as sills which will be anchored to the slab.
The slab has some unevenness after the removal of the block. I've hammered up as much of the old mortar to level it out. I'll use sill seal under the 4x4s but I'm still concerned about any gaps under.
Any recommendations for getting the best seal? Skim coat with mortar, lots of silicone or is there a right way to do it?



__________________
beachguy005 is offline  
 
Reply With Quote Quick reply to this message
Old 09-25-2012, 05:08 PM  
nealtw
Contractor
 
Join Date: Nov 2010
Location: vancouver, b.c.
Posts: 9,337
Liked 731 Times on 652 Posts
Likes Given: 1281

Default

4x4s will warp as they dry and get wet and dry again. You might be better off using 2x4 so it will better bend to the shape of the floor and use 2 or three layers of sill gasket.
And welcome to the site.



__________________
nealtw is offline  
 
Reply With Quote Quick reply to this message
Old 09-25-2012, 05:22 PM  
joecaption
Senior Member
 
Join Date: Jan 2011
Location: Hartfield VA, VA
Posts: 1,361
Liked 37 Times on 32 Posts
Likes Given: 2

Default

Post a picture of the whole thing.
Not sure why you would even think about using A 4 X 4 as a bottom plate.
How would you even attach it to the slab?

__________________
joecaption is offline  
 
Reply With Quote Quick reply to this message
Old 09-26-2012, 11:19 AM  
beachguy005
Senior Member
 
Join Date: Sep 2012
Posts: 129
Liked 33 Times on 31 Posts

Default

What I decided to do is just use some sand topping mix .5 to .75 inch thick and bed and level the 4x4 on top, secured with wedge anchors.
No concerns with it getting wet as it's will be covered with pt ply and pvc or Hardie trim.
Thanks for your input.

__________________
beachguy005 is offline  
 
Reply With Quote Quick reply to this message
Old 09-26-2012, 05:08 PM  
nealtw
Contractor
 
Join Date: Nov 2010
Location: vancouver, b.c.
Posts: 9,337
Liked 731 Times on 652 Posts
Likes Given: 1281

Default

Best, let them dry for a month and reject the warped ones!

__________________
nealtw is offline  
 
Reply With Quote Quick reply to this message
Old 09-27-2012, 03:22 PM  
joecaption
Senior Member
 
Join Date: Jan 2011
Location: Hartfield VA, VA
Posts: 1,361
Liked 37 Times on 32 Posts
Likes Given: 2

Default

Big mistake, but wish you the best.
Your going to have to use ACQ approved fastners for the studs and the sheathing or there just going to rust off.



__________________
joecaption is offline  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Crown/trim gaps crackur Carpentry and Woodworking 2 02-11-2011 02:45 PM
Repositioning bricks to close gaps in veneer? golem Bricks, Masonry and Concrete 0 11-12-2010 12:49 PM
Laminate Floor end gaps djensen Flooring 4 03-24-2010 07:23 AM
Gaps in stairs bsj40052 Carpentry and Woodworking 4 03-09-2010 08:58 PM
Need Advice on Filling low spot on Concrete Slab patio. DebbieG Bricks, Masonry and Concrete 4 06-03-2008 07:33 AM