DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Bricks, Masonry and Concrete > Garage Floor resurfacing options




Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old 11-16-2009, 02:09 PM  
grins
Junior Member
 
Join Date: Nov 2009
Posts: 1
Default Garage Floor resurfacing options

Hi Y'all!

I've got questions about my garage floor. I think it's about 50 years old, and there are no cracks in the floor. At one point it was covered with asphalt tile. However, significant areas of the floor have lost the tile and the top layer of concrete so that the gravel is exposed (is this called "spalling"?). The areas of exposure are 30-40% of the floor. It's hard to tell how much has worn away since the areas are large, but there are two points where the spalling is about 3/4 of an inch deep, the two spots near the bottom of this photo:



Here's the exposed gravel



So what are my options for this floor? I'm assuming I don't need to remove and replace the concrete since, with no cracking, it seems to be structurally sound. Can it be "skim-coated" with concrete? Will one of those acrylic coatings be able to effectively seal the concrete and prevent further spalling? Of course I'll need to remove the asphalt tile for an acrylic resurfacing--what about the mastic under the tile, does that need to be removed as well for the acrylic to bond?

I sure do appreciate your help



__________________
grins is offline  
 
Reply With Quote Quick reply to this message
Old 11-18-2009, 03:23 PM  
Nestor_Kelebay
Emperor Penguin
 
Nestor_Kelebay's Avatar
 
Join Date: Mar 2009
Location: Winnipeg, Manitoba
Posts: 1,844
Liked 2 Times on 2 Posts

Default

No, spalling occurs when water gets into concrete and it subsequently freezes. The pressure of the expanding water/ice inside the concrete causes the concrete to break where it's least able to oppose any breaking, and that occurs as "chips" of concrete break off at the surface of the concrete. This typically happens on the surface of a concrete foundation where water has been absorbed into the concrete and subsequently freezes.

What you have there is deterioration of weak concrete at the surface. That deterioration occurs when concrete is weak only at the top surface, usually because of a heavy rain falling on the concrete before it was cured enough to be resistant to moisture. Normally, the resulting concrete is weak only an inch or two deep at the most, and is of normal strength deeper than that. But, I guess it would depend entirely on how wet the concrete was when it got rained on, and how badly it rained. It's the "watering down" of the concrete by the rain that causes it to be weaker than it should be, and that's why the weaker surface concrete is easily worn off to expose the aggregate (stones) just below the surface. If there are only areas on your garage pad that are deteriorated, then it could be that the rain drained into those areas, or that the rain fell just as the concrete was curing to the point where it was resistant to moisture so that some areas were more affected than others.

(I'm not 100 percent sure about the concrete below the weakened layer being as strong as normal, so maybe confirm that with any concrete contractor listed in your yellow pages.)

Fresh concrete will not bond to cured concrete. If you want to level this floor, you need to use an epoxy or latex CONCRETE BONDING AGENT to literally glue the fresh new concrete you put on top to the old concrete.

I've never used an epoxy concrete bonding agent, but I know that you can get epoxies that can be applied underwater to effect a repair. I presume that you simply paint the epoxy concrete bonding agent onto the rough concrete, and pour the new concrete onto it.

Basically, the difference between a latex concrete bonding agent and white wood glue is that white wood glue will re-emulsify if it gets wet and stays wet for a while, even if it's been dry for decades. A concrete bonding agent has a window of time after it first dries that it will re-emulsify back into glue. After that window of opportunity has passed, a chemical reaction occurs within the latex bonding agent that renders it unaffected by moisture. So, the procedure would be to paint the latex concrete bonding agent on the deteriorated concrete and allow it to dry to the touch. Then pour the new concrete onto the concrete bonding agent and finish the concrete so that it's smooth. The moisture from the fresh concrete will re-activate the latex concrete bonding agent so that the bonding agent adheres to both the old and new concrete surfaces. Then, just allow the concrete to cure, and the old and new concrete will be bonded together when it does.

If you intend to do this work yourself, then you will notice that the bagged concrete mixes in your hardware store will give thickness ranges that you can use them for. For example, the bag might say: "Can be used to a 1/2 inch thickness." or "Can be used to a 0 inch thickness." The thickness the concrete mix can be used for has nothing to do with the concrete itself, but is determined by the size of the largest stones inside the bag. So, if they used stones in the concrete mix are no larger than 1/2 inch in diameter, then the concrete mix can't be spread any thinner than 1/2 inch thick. Concrete mixes that can be feather edged down to (effectively) 0 inches in thickness won't contain any stones, but will just have fine sand in them as the aggregate.

Typically, what you'll find under asphalt tiles is "black out" or black asphaltic adhesive. Some people mistake that for "tar" or "asphalt". There are solvents you can buy to remove this black out, but if you're planning to resurface much of the garage floor anyhow, I'd suggest that you go to any place that sells flooring installation supplies and ask about renting an electric floor stripper. Phone any place that sells flooring (like carpet), ask to talk to the Installations Manager and ask him who sells flooring installation supplies in your area. That place will also normally both rent and sell electric floor strippers. I expect you might also be able to rent them from most tool rental places as well. Maybe get some spare blades for it, too.

http://www.craintools.com/fs-more_pages/fs-700.html

PS: Never try to use an electric floor stripper on a wood floor because it'll chew up the wood somethin awful. These tools are really only meant to be used on concrete floors.

__________________

Last edited by Nestor_Kelebay; 11-18-2009 at 03:48 PM.
Nestor_Kelebay is offline  
 
Reply With Quote Quick reply to this message
Old 11-19-2009, 05:55 AM  
itsreallyconc
Senior Member
 
Join Date: Sep 2009
Location: hilton head & atl, sc & ga
Posts: 287
Liked 1 Times on 1 Posts

Default

this is our work & ANYTHING that remains on the floor's call'd a ' bond-breaker ',,, we'd use our conc scarifiers ( united rental, rsc, sunbelt ) to resurface the existing floor then o'lay w/polymer-modified conc ( skim-coat ),,, since the scarifier leaves a textur'd ( corduroy ) floor, we'd use 2 coats & possibly 3.

from the pics, its looks as if its just paste wear - even MY driveway's showing some wear as the downspout drained out on it leaving some pastewear.

spalling normally occurs near jnts & crks more often than in the open floor,,, typically, they're the result of slab movement or loads moving across jnts.

the ONLY thing we buy from an apron store is the plastic bags to hold our waste but its your garage !
__________________
itsreallyconc is offline  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Epoxy paint for garage floor MoJoe Flooring 6 06-23-2011 06:10 PM
Resurfacing stair treads now covered with carpet. What options are available? ranpan2009 Flooring 2 02-02-2010 08:44 PM
Garage Floor Buckling pressureseal Framing and Foundation 2 09-27-2009 05:39 PM
Resurfacing Concrete Floor & acid stain floor SPISurfer Flooring 13 12-18-2008 01:54 PM
Leveling Garage Floor YADAX3 General Home Improvement Discussion 2 04-14-2007 08:07 AM