DIY Home Improvement, Remodeling & Repair Forum

DIY Home Improvement, Remodeling & Repair Forum (http://www.houserepairtalk.com/forum.php)
-   Bricks, Masonry and Concrete (http://www.houserepairtalk.com/f17/)
-   -   Old Exterior Wall, Needs Door (http://www.houserepairtalk.com/f17/old-exterior-wall-needs-door-4565/)

DadOfFour 07-06-2008 08:40 PM

Old Exterior Wall, Needs Door
 
Ok, so I've got what used to be an exterior wall (thanks to an addition it's now an interior wall) that is a solid brick wall. I need to put a door way in it, no door just a doorway. I'm wondering if I can DIY or if I need to hire somebody to cut the opening. Actually, I'm not worried about cutting the opening, I can handle that. However I'm concerned about putting in the header. What exactly is involved in this and how much skill do you really need to DIY?

hondadrv24 07-07-2008 10:12 AM

Welcome DadofFour,
building your header is a fairly simple concept. I would assemble your 2x10 to the outer king studs before putting them up in place. Make sure to put some plywood between the 2x10s so that they are tied together and are the same width as your king studs. Then fasten the king studs to the brick. after you have that completed put 2 more 2x4s up so they touch the floor and the 2x10 and nail them to the king studs, these are the ones that hold the weight. then its just a matter of trimming out the opening.

here is the basic image of what you are making

http://i292.photobucket.com/albums/m...89/doorway.jpg
Justin

DadOfFour 08-04-2008 07:42 PM

Quote:

Originally Posted by hondadrv24 (Post 20859)
Welcome DadofFour,
building your header is a fairly simple concept. I would assemble your 2x10 to the outer king studs before putting them up in place. Make sure to put some plywood between the 2x10s so that they are tied together and are the same width as your king studs. Then fasten the king studs to the brick. after you have that completed put 2 more 2x4s up so they touch the floor and the 2x10 and nail them to the king studs, these are the ones that hold the weight. then its just a matter of trimming out the opening.

Justin

Thanks for the reply! Are you talking about putting a wood door frame inside of the opening to support the brick? I guess I could do that, however I was kind of thinking that I'd like to have the exposed brick edges, is there a way to do that?

glennjanie 08-05-2008 02:55 PM

Welcome DadOfFour:
This can be a dangerous project with a complete wall collapse.
I would want to cut the mortar joint out at the height you want and insert an angle iron lintel before cutting the opening. This may need to be done on both sides of the wall if it is more than 1 brick thick.
Glenn

DadOfFour 08-05-2008 07:53 PM

As if it wasn't complicated enough already......

I just went to the house again today and looked at where the door needs to go and I've discovered that on one side of where the doorway will be is what appears to be an old window that has been replaced with a simple bookshelf unit. Thus, when I pull the bookshelf out half of one side of the doorway will be unsupported. I'm starting to think that maybe I should just have a contractor come in and do this....any tips?

inspectorD 08-06-2008 06:09 AM

YUp
 
Professional set of eyes lookin at it.:eek:
Sometimes you can work something out with a contractor, but then they are not liable if you do....so let em work and give yourself another project. I'm sure there is something on the honeydew list.:D


All times are GMT -6. The time now is 07:37 AM.