DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Framing and Foundation > Framing basement partition - ceiling not level




Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old 07-26-2010, 09:34 AM  
gqskrub
Junior Member
 
Join Date: Jul 2010
Posts: 1
Default Framing basement partition - ceiling not level

Hi I'm building a rather simple wall in my basement to separate space. However the ceiling towards the middle of the room is 1.5'' shorter than at the edge of the room. The base plate needs to be shimmed but only about 0.25''. That still leaves over an inch of space above the frame at the edge of the wall. What should I do?

<edit> I wanted to build the wall laying down and then tilt it into place. I was not sure whether shimming 1'' would be too much or if it would be better for me to cut the vertical studs at varied heights and have the top plate at the same angle as the ceiling. </edit>



__________________

Last edited by gqskrub; 07-26-2010 at 10:27 AM.
gqskrub is offline  
 
Reply With Quote Quick reply to this message
Old 07-26-2010, 07:27 PM  
kok328
Supporting Member
HRT_SUPPORTER.png
 
Join Date: Nov 2007
Location: Grand Blanc, MI
Posts: 2,165
Liked 99 Times on 87 Posts
Likes Given: 61

Default

I'd shim the top plate after the wall is assembled and lifted into place. That way you don't have to keep accomodating the difference in heigth with the drywall to follow.



__________________
kok328 is offline  
 
Reply With Quote Quick reply to this message
Old 08-10-2010, 07:21 PM  
BrianKiernan
Member
 
Join Date: Aug 2010
Posts: 42
Default

Either way would be fine. For me I would just cut each stud to fit.

Install bottom plate, level up each end and mark the top, snap line and install top plate.

Lay out studs and measure each and write on scrap wood. Cut each stud at once then nail up one at a time.

Just my .02

Good Luck

__________________

Good Luck,
Brian
[URL="http://www.install-crown-molding.com"][COLOR="Blue"]http://www.install-crown-molding.com[/COLOR][/URL]

BrianKiernan is offline  
 
Reply With Quote Quick reply to this message
Old 11-04-2010, 05:48 PM  
nealtw
Contractor
 
Join Date: Nov 2010
Location: vancouver, b.c.
Posts: 9,267
Liked 721 Times on 643 Posts
Likes Given: 1266

Default

either way is good , stick framing will feel better when your done if pride means anything

__________________
nealtw is offline  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
basement framing mgoblue24 Framing and Foundation 4 01-23-2010 02:47 PM
Framing basement matt s Carpentry and Woodworking 3 11-27-2009 08:10 PM
Split-Level Framing Question kobelleprop General Home Improvement Discussion 5 04-27-2008 11:25 AM
Framing For a Drywall Ceiling: tomtoolman12345 Framing and Foundation 4 03-10-2008 07:33 AM
Working Around Old Basement Framing pressureseal Flooring 9 01-17-2008 06:10 AM