DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Framing and Foundation > framing bid jargon




Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old 07-06-2009, 07:57 PM  
daleslad
Member
 
Join Date: Apr 2008
Posts: 30
Default framing bid jargon

Need some expert help here mates, a friend got this bid for his workshop and wanted me to decipher it for him so that he could decide what he was getting was what he wanted from the contractor.

Framing to sheeting
Slab on grade daylight
6/12-pitch truss roof
12’ plate heights
Square garage wrap
Plumb cut tails
2X4 sub-fascia with 4/4X6
Exterior soffit backing
Strip wrap and set 4 exterior windows and 2- 3/0door

Thanks
Cheers



__________________
daleslad is offline  
 
Reply With Quote Quick reply to this message
Old 07-07-2009, 06:37 PM  
GBR
Senior Member
 
Join Date: Mar 2009
Posts: 337
Liked 18 Times on 17 Posts
Likes Given: 9

Default

Framing to sheeting---doing the framing(building) sheeting(sheathing) needs to specify roof and wall
Slab on grade daylight---Just a slab-no footings below frost grade, on existing grade, he won't dig or level it. Daylight usually is open on one side(back) rest is buried in hillside with concrete walls. Wrong application here.
6/12-pitch truss roof---Means 6/12 cut or rises 6" in 12" horizontally
12’ plate heights--- Studs and plates = 12' total
Square garage wrap--- in top corner detail as opposed to 45* corners, wrap is the trim-jambs and head boards
Plumb cut tails--- end of rafters past building are cut vertically.
2X4 sub-fascia with 4/4X6---2x4 nailed to rafter tails before trim, 4/4x6 may be look-outs to hold up barge rafter
Exterior soffit backing--- only installs the backing member horizontally at the building for a closed soffit
Strip wrap and set 4 exterior windows and 2- 3/0door---installing and weatherproofing the windows and doors but no drip flashing

You get to finish everything he doesn't mention, a lot! The roofing, vents, barges, rake trim on roof, closed soffit finish material, vents, window trim, finished siding, blocking for same, flashing, footings- required by code in CA, flashing over windows and doors. He is doing about 1/2, make sure to get a permit as his quote is very lacking in detail. Get 2 other estimates which will be a lot higher as he is leaving a lot out and only sitting on a slab. Be safe, G

__________________
GBR is offline  
 
Reply With Quote Quick reply to this message
Old 07-07-2009, 06:49 PM  
daleslad
Member
 
Join Date: Apr 2008
Posts: 30
Default

Thanks GBR, that helped a lot. I will pass on the advice about checking out the rest of the stuff that should be covered.

__________________
daleslad is offline  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Foundation and Framing jgambie Framing and Foundation 3 06-03-2008 05:47 AM
Are screws of for framing? SeattleDIY General Home Improvement Discussion 6 06-02-2008 10:55 AM
What is balloon framing? billbeee Framing and Foundation 2 05-28-2008 06:45 PM
Help deciphering framing in pic TaskBoy Framing and Foundation 4 05-18-2008 04:18 PM
Framing question GolfnRL Framing and Foundation 6 03-25-2008 03:37 PM