DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Framing and Foundation > Girl needs help! Water damaged sill





Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old 05-30-2009, 09:44 PM  
Georgiagirl
Junior Member
 
Join Date: May 2009
Posts: 1
Default Girl needs help! Water damaged sill

First, I am new to this site so please be nice and redirect me to the correct place if necessary.

My house was built in 1942. I have lived here for just over a year with no real concerns. Currently I have ripped off the vinyl siding only to reveal the original clap board siding which was in very bad condition and is now gone as well. However I have discovered that the sill, I believe this is the correct term for it, has an area approximately 8 feet in length directly below the bay window which has had some significant water and probable but not current termite damage to it. The clap board was so rotten it fell off the house when I tapped it with the hammer. I have read a few threads regarding replacement of this section and I would just like someone to clarify a few points for me please.

The beam is 10"x4". Is it ok to replace it with 2, 10"x2" boards, and if so should I brace them together before I fit them into place and what is the best way do this (hurricane brace, screws, nails, ect.) Can I replace the entire section in one piece or should I do two 4' sections. Exactly how do I secure these boards to the brick foundation as I cannont tell upon examination how or where the other parts of this beam are secured to it.
I have placed some support boards under the horizontal 2x4 for support of the wall, but it should be noted that there is no sag in the wall, window or flooring on the exterior of the home or on the interior of the home. So is it ok to leave these here while I replace the sill or do I need additional support elsewhere. I am planning on moving the supports to the 2x4 directly under the window sill afterwards in order to replace that particular 2x4 that they are resting under right now(see photo). Is it ok to support the wall in this place as well.
The subflooring directly above the sill is rotted as well, but it should be noted that underneath, in the crawl space there is no rotting of the floor joists, also noted that the floor joist do not sit on this beam for support they are notched out and sit directly on the brick foundation and butt up against the beam perpendicularly. Do and Can I replace this section of the subfloor from under the crawl space without disturbing the flooring inside the house (as it is the original hardwood floor!), and how far back should I make the cut? The flooring from the crawlspace going up in layers looks like: 1x10's running diagonally across the floor joists ( the outer 4 inches of which is rotted) then a thin layer of plywood? not rotten. Then some other layer which does not seem to be affected either.

I have attached a picture for your viewing pleasure. I would appreciate any advice you can give me.





__________________

Last edited by Georgiagirl; 05-30-2009 at 09:56 PM.
Georgiagirl is offline  
 
Reply With Quote Quick reply to this message
Old 06-05-2009, 03:05 PM  
comcarcab
Junior Member
 
Join Date: May 2009
Posts: 7
Default

Hi there
Before you do anything you should make sure that the building is adequately supported,by the look from the photo those 2x4's are not nearly enough to do the job.You should also get some advise about code from your city building inspector before removing the beam ,you may not be able to put it back as it was with updated codes etc.In my experience here in S Florida the city will want you to put in a 4x10 continuous length beam which will be very heavy, so you are probably going to need some help.
It really does look like an awful lot of work for an inexperienced person,is there maybe a friend that can help or even give some professional guidance.
If you are able to ask the city inspector to come out to your home,they will then tell you what is required and how to go about doing it.
I hope this is of some help
Good luck with the project.

__________________
comcarcab is offline  
 
Reply With Quote Quick reply to this message
Old 06-25-2009, 08:09 PM  
spaz2965
Member
 
spaz2965's Avatar
 
Join Date: Oct 2008
Location: Jefferson, York county pa
Posts: 84
Default

Looking at the picture you are referring to the band board. Your floor joist should be running into that and should be sitting on you foundation wall by at least 3". If this is the case you should be able to remove that section, which I would go at least 8" past each side of the window. You may use 2x10 for your new band board. If you are concerned, you my go inside and support the floor while you fix the band board.
Hope some of this helps!

__________________
spaz2965 is offline  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Water damaged flooring Sunnygal Flooring 3 08-04-2008 01:04 PM
A girl and an old house mockinbird Introductions 6 07-28-2008 06:28 AM
Hello from the new girl NotYet Introductions 0 08-21-2007 09:17 PM
Water damaged wall. Shark Introductions 0 08-04-2007 02:45 PM
More Water Damaged Framing with Pictures JKTrevecca Framing and Foundation 7 02-13-2007 09:41 PM