DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Framing and Foundation > Header problems




Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old 02-05-2008, 08:59 AM  
electech46
Junior Member
 
Join Date: Feb 2008
Posts: 1
Default Header problems

Hello all,

I'm in the process of remodeling my kitchen and have recently discovered my (latest) unforseen issue. The house was built in 1956 it is a single story house with a full basement. About 25 years ago my wife had her uncle (supposedly a carpenter) replace a double window in the kitchen with a sliding glass door. In the process they really messed up the header which was above the old window. They actually cut the jack stud and king studs and removed them from one side of the header and left it unsupported. I can see where the roof has sagged and this actually answers some questions I was having with other framing problems I was having. It looks like the roof has sagged about 1/2" since that is the space I have between the cap plate and the header on both ends (the cap plate is still in contact with the header in the middle). I know I need to replace the header with a new one that is 4" longer than the current one and will replace it with 2 2x10 nailed together. What I don't know is how to get the roof back up to where it needs to be. Can anyone offer any advice?



__________________
electech46 is offline  
 
Reply With Quote Quick reply to this message
Old 02-05-2008, 09:39 AM  
Daryl in Nanoose
Senior Member
 
Daryl in Nanoose's Avatar
 
Join Date: Feb 2006
Location: Nanoose Bay, BC
Posts: 762
Liked 3 Times on 3 Posts
Likes Given: 5

Default

This is what I've done in the past. I think my pic tells all.



untitled.jpg  
__________________

[url]http://edhome.shawwebspace.ca/[/url]

Daryl in Nanoose is offline  
 
Reply With Quote Quick reply to this message
Old 02-05-2008, 06:00 PM  
hondadrv24
Senior Member
 
Join Date: Feb 2008
Posts: 188
Liked 1 Times on 1 Posts

Default

I think that you could install the jack and king studs on one side, put the header up, and attach it in several spots to the cap plate, as best as possible as it would be leaning down at the other end, use a 4x4 under the other end of the header on top of the jack and then jack it up until you could get the studs underneath at the other end.

Just a thought have not done it before, good luck

__________________
hondadrv24 is offline  
 
Reply With Quote Quick reply to this message
Old 02-05-2008, 07:30 PM  
guyod
Senior Member
 
Join Date: Jan 2008
Location: Wind Gap, PA
Posts: 423
Liked 21 Times on 20 Posts
Likes Given: 8

Default

First I would toenail the header in at the center so the header stays up on its own then cut your 2x4's to the height that it should be and angle it in place. Then start jacking up in the center then using a sledge hammer start banging the 2x4's in place on each side. take your time . Pump the jack about 2 times then bang both 2x4 evenly til you cant move them any more then jack some more.. Repeat.

make sure the post you use on top of the jack is cut perfectly on a 90 angle and use level use a 4 foot level on it before you put any real weight on it.

I jacked up a 22' open span about an inch doing something simular. little different senerio than yours but i kicked out the jack about a dozen times no matter how level i got the post just because of the massive weight.. its a scary thing watching the jack and post slowly start push out.

__________________
guyod is offline  
 
Reply With Quote Quick reply to this message
Old 04-30-2008, 09:01 AM  
fred333
Junior Member
 
Join Date: Apr 2008
Posts: 22
Default

That is a very scary sight. The sense of having no power.



__________________
fred333 is offline  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Humidity/Condensation Problems davidhmail HVAC 6 04-16-2009 12:06 AM
garage door header butcher757 Framing and Foundation 6 09-10-2008 08:50 AM
Cutting header on load bearing wall Scrap Windows and Doors 3 08-10-2007 08:01 AM
Infrared for detecting electrical problems stollison Electrical and Wiring 2 06-14-2006 02:35 PM
Header over 10-12' patio door gregoryedgar General Home Improvement Discussion 7 06-05-2006 02:52 PM