DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Framing and Foundation > How do I open ceiling with rafter ties in the way?





Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old 02-10-2013, 09:00 AM  
sab
Junior Member
 
Join Date: Feb 2013
Posts: 5
Default How do I open ceiling with rafter ties in the way?

Description: Swiss chalet built as a summer home (Maine). Second floor ceiling has strapping nailed to the joists (rafter ties), with cardboard white tiles stapled to the strapping. The 1959 installed tiles is falling down plus I'm installing Andersen's on a gable ends and had to open the ceiling to reframe.

Q: The ceiling joints are 2"x 4" x 30'(?) and 20"-24" on center. What are my choices to open up the ceiling and install sky lights? Can the licensed contractor install LVL's like every 4' or something if I remove the ties? How can I open up the ceiling?



__________________
sab is offline  
 
Reply With Quote Quick reply to this message
Old 02-10-2013, 11:22 AM  
BridgeMan
Senior Member
 
BridgeMan's Avatar
 
Join Date: Aug 2011
Location: Cottage Grove, Oregon
Posts: 713
Liked 62 Times on 57 Posts

Default

Your post doesn't make sense. "Ceiling joints" are 2" x 4", 30' long? First I thought you meant "joists," but realized a 2 x 4 cannot span 30' without sagging terribly, just trying to support its own weight. How about a better description of what you actually have? And a few pictures and a sketch would help a lot, too.



__________________
BridgeMan is offline  
 
Reply With Quote Quick reply to this message
Old 02-10-2013, 11:59 AM  
sab
Junior Member
 
Join Date: Feb 2013
Posts: 5
Default

No one is standing on the joists they are covering the catherial ceilling of the chalet (there is no third floor). Yes they're 25 or 30' long because they where milled that way and they measure a real 2" x 4" (or 2.25 x 4.25). The house was problaly ordered from the mill and built in 2 or 3 days like dozens of others. Like a ocean beach cottage used for the summer months and converted to year round this is a lake cottage. That ocean beach cottage that cost 5K to build may be worth 500K today or more. BTW - Your right I had to sister the 2x8(?) on the 1st and 2nd floor because they were 24" on center and the floor was too bouncey.

__________________

Last edited by sab; 02-10-2013 at 12:10 PM.
sab is offline  
 
Reply With Quote Quick reply to this message
Old 02-10-2013, 09:08 PM  
nealtw
Senior Member
 
Join Date: Nov 2010
Location: vancouver, b.c.
Posts: 7,741
Liked 542 Times on 491 Posts
Likes Given: 1000

Default

Your rafters sound like they are well under designed and removing the collar ties would weaken the structure. I would get permits for the work and they may require an engineer, anything else is just guess work.

__________________
nealtw is offline  
 
Reply With Quote Quick reply to this message
Old 02-11-2013, 06:34 AM  
sab
Junior Member
 
Join Date: Feb 2013
Posts: 5
Default

Agree, As an engineer, I just wanted to understand what my options are and what the structural engineer is going to propose, if anything. I want to install a new roof, and if I install a new roof then I should install skylights, and if I install skylights then I need to open up the ceilling. That doesn't include the fixing furnace chimney thats tied into the fireplace chimney that pass through part of the roof. Looking forward to that condo in FL!

__________________
sab is offline  
 
Reply With Quote Quick reply to this message
Old 02-11-2013, 09:40 AM  
nealtw
Senior Member
 
Join Date: Nov 2010
Location: vancouver, b.c.
Posts: 7,741
Liked 542 Times on 491 Posts
Likes Given: 1000

Default

For the structure alone you would at least double up the rafter on each side of the window and hang a double above and below and then hang the cut rafters off that but the ties, maybe you get away with doubling those but I don't know.
But like Bridgeman mentioned the rafters a questionable.

__________________
nealtw is offline  
 
Reply With Quote Quick reply to this message
Old 02-11-2013, 09:47 AM  
Fireguy5674
Junior Member
 
Join Date: Dec 2012
Location: Jacksonville, Illinois
Posts: 163
Liked 27 Times on 23 Posts
Likes Given: 17

Default

Ok, let me rephrase your description and make sure I understand what you have. The 2.25 x 4.25 x 30' members are rafter ties to stabilize your roof from bowing in or out at the center of your rafter span. Attached to the bottom of these are some 3/4" (?) "straps" running perpendicular to your rafter ties to which your ceiling tiles are stapled. I am assuming probably roughly 12" x 12" tile size. Now you want to remove the tile, the strapping and every other rafter tie to open up the area and create a cathedral ceiling effect?

If I understand your intentions correctly, taking down the tiles and most of the strapping should not be a problem. I would not remove all the strapping because I would be concerned about a 30' long rafter tie wanting to bow sideways from the compression of roof load. A 2x4 or 2x6 could be added on top of the rafter ties to keep them from bowing. I would break the 30' span into at least thirds and run two rows the complete length of the roof similar to stabilizing the bottom chord of a truss.

I am like others here who are amazed that the rafter ties have not sagged. Are there any verticle supports going to the rafters anywhere along this 30' length? Also, what is the pitch of your roof and what is size and span of your roof rafters? These will make a difference in what you can do. If you decide to try to elimnate every other rafter tie, you will definitely need structural expertise. From an appearance standpoint instead of LVL's you might think about double 2 x ?'s (whatever the load requires) with spacer's which you can slide over both sides of the existing rafters and bolt through. In other words, two 2 x 8'2 (?) with a 2.25" spacers which you can fit over the rafters at the ends and bolt through. This approach might also eliminate the need for horizontal stabilization. Hope that is a little clearer than mud.

One more headache. Be careful when removing ceiling tile. I will be willing to bet that they contain asbestos. The are the right age for it.

__________________

Last edited by Fireguy5674; 02-11-2013 at 10:23 AM. Reason: Another thought.
Fireguy5674 is offline  
 
Reply With Quote Quick reply to this message
Old 02-11-2013, 10:32 AM  
BridgeMan
Senior Member
 
BridgeMan's Avatar
 
Join Date: Aug 2011
Location: Cottage Grove, Oregon
Posts: 713
Liked 62 Times on 57 Posts

Default

And with all the rafter ties gone, then the only problem will be how to bring the exterior walls back into alignment, because they will be bowing outward. I saw it happen on a place in the mountains of NM some years ago, where significant snow loads on the roof were an issue--the guy yanked all of the rafter ties, and then was surprised when both outside walls deflected outwards several inches, each. What a mess. He finally "corrected" the problem by installing 1"-dia. steel tie rods every 6' or so--looked ugly as sin, but they kept the walls from completely letting go.

__________________
BridgeMan is offline  
 
Reply With Quote Quick reply to this message
Old 02-11-2013, 11:31 AM  
nealtw
Senior Member
 
Join Date: Nov 2010
Location: vancouver, b.c.
Posts: 7,741
Liked 542 Times on 491 Posts
Likes Given: 1000

Default

I would like to see a photo of the inside, what about insulation?

__________________
nealtw is offline  
 
Reply With Quote Quick reply to this message
Old 02-11-2013, 11:53 AM  
sab
Junior Member
 
Join Date: Feb 2013
Posts: 5
Default

FireGuy5674 - your correct in your description. I'll see what the engineer says. I was thinking tie-rods would be the best solution. LVL most likely only provide compressive strength not tensile. The roof is 45 degrees (12/12 pitch). The roof overhangs the sidewall 2.5 feet. The second foor rooms are impacted by the slope of the roof. Thanks boys. I thought maybe there was a best practice to install tie rods or something. I can't be the only chalet owner you wants to do this.



__________________
sab is offline  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Insulate open rafter roof busyflyin Roofing and Siding 30 01-29-2012 11:30 PM
Open rafter ceiling cnelson0131 Insulation and Radiant Barriers 3 06-19-2011 09:20 PM
Rafter Ties cibula11 Framing and Foundation 2 01-20-2010 12:04 PM
Damaged rafter? rookie1234 General Home Improvement Discussion 7 04-15-2009 05:31 AM
Rafter tail rot jcmarco74 Roofing and Siding 4 01-14-2006 01:41 PM