DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Framing and Foundation > Jacking my Floor, Whatcha think???




Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old 07-07-2006, 09:26 AM  
harleysilo
Member
 
Join Date: Jul 2006
Posts: 61
Default Jacking my Floor, Whatcha think???

Here's the house to give some perspective on what I'm jacking....

Thanks!



__________________

Last edited by harleysilo; 10-29-2008 at 09:51 AM.
harleysilo is offline  
 
Reply With Quote Quick reply to this message
Old 07-07-2006, 09:28 AM  
harleysilo
Member
 
Join Date: Jul 2006
Posts: 61
Default



LImit 4 pics per post.


__________________
harleysilo is offline  
 
Reply With Quote Quick reply to this message
Old 07-07-2006, 03:23 PM  
Square Eye
Senior Member
 
Square Eye's Avatar
 
Join Date: Jan 2006
Posts: 1,273
Liked 4 Times on 4 Posts

Default

I think you're doing fine. Nothing will support the floor like a wall. I have seen often, that a main girder will run down a hallway under one wall, and the wall on the other side will still have enough load to cause the joists to sag 3' from the main girder. Support issues will drive you nuts. Most building inspectors and firefighters hate those basement jacks. Be careful using them. When you raise that big jack in the center, the two basement jacks could fall on you.

Be extremely careful, this is the kind of work that can get you seriously hurt.

Oh! welcome to the forum Nathan.
Tom

__________________

[URL="http://www.houserepairtalk.com/announcement.php?f=39&a=6"][size=3]The Ten Commandments of House Repair Talk[/size][/URL]



[URL="http://home.bellsouth.net/p/s/community.dll?ep=16&groupid=289528&ck="]Square Eye's home page[/URL]

Square Eye is offline  
 
Reply With Quote Quick reply to this message
Old 07-08-2006, 06:56 AM  
harleysilo
Member
 
Join Date: Jul 2006
Posts: 61
Default

Thanks for your reply.

__________________

Last edited by harleysilo; 10-29-2008 at 09:52 AM.
harleysilo is offline  
 
Reply With Quote Quick reply to this message
Old 07-08-2006, 09:39 AM  
inspectorD
Housebroken
HRT_MODERATOR.png
 
inspectorD's Avatar
 
Join Date: Dec 2005
Location: Litchfield, CT
Posts: 3,934
Liked 94 Times on 81 Posts
Likes Given: 189

Default Looks good

When you look at where the beam is compared to where the load bearing wall is you should be no more than a 45 degree angle.

That is rule of thumb anyway, like the cone of compression in soil.

Just make sure those hangers you are putting in have the correct fasteners, no screws.

Good luck on your project,

__________________

Just My
Made in the

inspectorD is offline  
 
Reply With Quote Quick reply to this message
Old 07-08-2006, 07:48 PM  
harleysilo
Member
 
Join Date: Jul 2006
Posts: 61
Default

Well, $300 later and about 9 hrs by myself and jacking has comenced....

I'll post the results on Monday, pics included....

Looks like my 3 setups are getting all joist except the one under one wall, so one more 20 ton'er on the end of one 4x6 beam and that should do it.

__________________
harleysilo is offline  
 
Reply With Quote Quick reply to this message
Old 07-09-2006, 03:01 PM  
LoneJeeper
Member
 
Join Date: Jun 2006
Posts: 32
Default

Quote:
Originally Posted by harleysilo
Thanks, I'm glad I found it!
Glad you found it, eh? I'm unappreciated in my time.

hope it all goes well for ya.

lj
__________________
LoneJeeper is offline  
 
Reply With Quote Quick reply to this message
Old 07-10-2006, 07:58 AM  
harleysilo
Member
 
Join Date: Jul 2006
Posts: 61
Default

Metal post just hanging there by two nails. So I secured the joists under the kitchen wall and let everything back down onto the metal post, allbeit everything (floor joists) are still .5 inch higher than the were before I started...as evident in this pic of the previous DIY'er wall header staying attached to the jacked joists.

__________________

Last edited by harleysilo; 10-29-2008 at 09:52 AM.
harleysilo is offline  
 
Reply With Quote Quick reply to this message
Old 07-10-2006, 07:59 AM  
harleysilo
Member
 
Join Date: Jul 2006
Posts: 61
Default

Best pic I could come up with to descripe it...

__________________

Last edited by harleysilo; 10-29-2008 at 09:52 AM.
harleysilo is offline  
 
Reply With Quote Quick reply to this message
Old 07-10-2006, 11:12 AM  
Square Eye
Senior Member
 
Square Eye's Avatar
 
Join Date: Jan 2006
Posts: 1,273
Liked 4 Times on 4 Posts

Default

The house may have been built a little off. Raising the floor to level when the house was built with a sag in the floor will bring this kind of thing up.

OR

Has there been a repair done in that area previously? If so, they may have masked the problem and now that you are fixing the problem correctly, the previous repair has become another problem for the list!

Dominos. Fix one thing and that breaks another.

Doing it right, like you have been doing, will eventually make all of it right.

Press on.



__________________

[URL="http://www.houserepairtalk.com/announcement.php?f=39&a=6"][size=3]The Ten Commandments of House Repair Talk[/size][/URL]



[URL="http://home.bellsouth.net/p/s/community.dll?ep=16&groupid=289528&ck="]Square Eye's home page[/URL]

Square Eye is offline  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Need input on Jacking up house Sheryl Framing and Foundation 33 06-09-2013 08:34 AM
Jacking Barn welda Framing and Foundation 2 05-12-2008 07:18 PM
jacking up wall tandem10 Framing and Foundation 1 04-30-2007 08:04 PM