DIY Home Improvement, Remodeling & Repair Forum

DIY Home Improvement, Remodeling & Repair Forum (http://www.houserepairtalk.com/forum.php)
-   Plumbing Forum (http://www.houserepairtalk.com/f33/)
-   -   bathtub overflow?? (http://www.houserepairtalk.com/f33/bathtub-overflow-7730/)

Rob99 10-10-2009 08:15 PM

bathtub overflow??
 
Hi guys

I've just noticed that after my upstairs tub was used, the ceiling in my living room directly below was wet. The caulking is fine I'm suspecting it's the bathtub overflow because I'm told the tub was filled to the top and I think water got in there.

I took off the cover and it looks like the previous owner just tried filling the hole with caulking since there were globs in there.

Is it worth the hassle of fixing it properly which would probably include making a hole in the ceiling to gain access, or would you just seal off the overflow and make sure whoever uses that tub never fills it that high?

thanks.

kok328 10-10-2009 08:21 PM

I'd be willing to let it go. As long as the tub isn't filled to a point where if someone gets in it after filling it, the level would overflow onto the floor.

Cork-Guy 10-10-2009 08:22 PM

Well, if you can make sure no one uses it again that is a solution. However, are you sure it's the overflow? It could be another underlying problem and it might be worth checking it out and turning a future problem in a solution. :)

Rob99 10-10-2009 08:27 PM

Quote:

Originally Posted by kok328 (Post 35539)
I'd be willing to let it go. As long as the tub isn't filled to a point where if someone gets in it after filling it, the level would overflow onto the floor.

It is the guest bathroom and it's been used a total of once in the past 2 years. I'm leaning this way.

Quote:

Originally Posted by Cork-Guy (Post 35540)
Well, if you can make sure no one uses it again that is a solution. However, are you sure it's the overflow? It could be another underlying problem and it might be worth checking it out and turning a future problem in a solution. :)

The reason I think it's the overflow is because I couldn't recreate the leak. The leak happened last week. Yesterday I ran the water for about 10 mins and wet stains on the ceiling. I then filled the tub half way and let it sit for a while, then drained it. No wet stains on the ceiling.
I then removed the valve cover and ran the shower for 10 minutes to see if any water was leaking behind the wall. No leak.

The only thing left is the overflow I'm thinking.

thanks for the replies.

Redwood 10-11-2009 07:27 AM

Look at the overflow gasket in between the tub and overflow.
Another possibility is the screws on the overflow plate are loose.

Rob99 10-11-2009 09:18 AM

Quote:

Originally Posted by Redwood (Post 35551)
Look at the overflow gasket in between the tub and overflow.
Another possibility is the screws on the overflow plate are loose.

Looks like this is it.
There appears to be a small gap between the overflow pipe and the actual hole in the tub that's not caulked so rising water would seep through that crack before reaching the level of the overflow pipe. There's a gasket for this? I was thinking of just caulking that gap.

Nestor_Kelebay 10-11-2009 02:36 PM

Rob99:

I've replaced that beveled washer behind the overflow, and plumbers here in Winnipeg do it from inside the bathtub. You simply take the crossbar out and push the overflow drain pipe far enough back to slip the old gasket off and slip a new one on.

I'd like to hear what Redwood says on this, but I know for a fact that I've replaced that gasket without causing another leak at the joint where the tee where the overflow and drain pipes meet.

The gasket is a beveled type, very similar to the one that goes between a toilet flush valve and the toilet tank, only a little smaller.

Redwood 10-11-2009 06:26 PM

Yes Nestor that is how I do it as well unless there is already access from behind.
Many use a gasket like the one pictured below that is tapered.
The thin part goes to the top.

http://i44.photobucket.com/albums/f2...9/7cbb28b3.jpg

Some use a slightly different gasket that have 2 ears that clip over the waste and overflow like the one pictured below. Kohler I think is one that does.

http://i44.photobucket.com/albums/f2...9/41c57e8c.jpg

Leontyne Lilibeth 11-07-2009 02:46 PM

I have a bathtub overflow plate that was removed. However the screws were so old that they snapped. I tried a pliers to remove them without any luck. Anyone have any other suggestions?

travelover 11-07-2009 06:24 PM

Quote:

Originally Posted by Leontyne Lilibeth (Post 36510)
I have a bathtub overflow plate that was removed. However the screws were so old that they snapped. I tried a pliers to remove them without any luck. Anyone have any other suggestions?

Use a screw extractor or similar tool. It requires that you drill a hole in the middle of the broken off screw. Sometimes drilling the hole with a left hand drill will cause the screw to back out

Screw Extractors | Bolt Extractor | Square Easy Out | Spiral Easy Out

You might also be able to slot the stub with a small saw blade or Dremel wheel and back it out with a flat bit screwdriver.

How to Remove a Broken Bolt | eHow.com


All times are GMT -6. The time now is 05:02 PM.