DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Plumbing Forum > Help Identifying A Leaky Kitchen Faucet




Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old 04-28-2014, 12:41 AM  
LeakingFaucet
Junior Member
 
Join Date: Apr 2014
Location: San Francisco, CA
Posts: 27
Liked 5 Times on 4 Posts

Default Help Identifying A Leaky Kitchen Faucet

Can anyone tell me who makes this faucet? I'm looking to replace an o-ring that has literally disintegrated and now causes water to leak out the shower holes even when the handle is not compressed. I'll try to describe what is happening but I'm not sure of all the technical terms.

The handle can be compressed. When in the open position, the water runs through a 1" diameter aerator. When the handle is compressed, the water is routed to holes surrounding the aerator that cause a shower.

The handle pushes a piston which diverts the water to either go through the aerator or through the many holes for the rain shower. The piston has an o-ring that moves to block or open the pathway for water to run to the aerator. Since the o-ring is gone, when the handle is pushed, water flows both the aerator and the rain shower holes.

I hope if someone could tell me who makes this faucet, then I could try look up the side of the o-ring that is wrapped around the piston. I've tried a few size o-rings from Home Depot but none fit just right.



img_2988.jpg  
__________________
LeakingFaucet is offline  
 
Reply With Quote Quick reply to this message
Old 04-28-2014, 07:51 AM  
CallMeVilla
Contractor
 
CallMeVilla's Avatar
 
Join Date: Feb 2010
Location: San Diego
Posts: 1,262
Liked 385 Times on 301 Posts
Likes Given: 157

Default

Manufacturer stamps are located on the reverse side of the neck, at the base. Why do they do that? it is almost impossible to read if it is against a backsplash? Got me.

Use a mirror and flashlight. My last encounter like this, I thought the faucet wand was from Delta but turned out to be from Grohe. You just have to find it.

Good news: Nearly all manufacturers will send you repair parts for free for life. So, it is worth the work.



leaking-faucet.jpg  
__________________
CallMeVilla is offline  
 
Reply With Quote Quick reply to this message
Old 04-28-2014, 10:28 PM  
LeakingFaucet
Junior Member
 
Join Date: Apr 2014
Location: San Francisco, CA
Posts: 27
Liked 5 Times on 4 Posts

Default

Alright, I checked behind the neck at the base and no luck. Here's what it looks like.

img_2996.jpg  
__________________
LeakingFaucet is offline  
 
Reply With Quote Quick reply to this message
Old 04-28-2014, 10:29 PM  
LeakingFaucet
Junior Member
 
Join Date: Apr 2014
Location: San Francisco, CA
Posts: 27
Liked 5 Times on 4 Posts

Default

I also pulled the handle off so now it's detached from the base. It looks like some kind of glue was holding it on there, vs a screw. What type of glue/epoxy would you recommend I use to put it back on?

img_2995.jpg  
__________________
LeakingFaucet is offline  
 
Reply With Quote Quick reply to this message
Old 04-28-2014, 10:34 PM  
LeakingFaucet
Junior Member
 
Join Date: Apr 2014
Location: San Francisco, CA
Posts: 27
Liked 5 Times on 4 Posts

Default

Here is a sequence of photos showing how I get to the busted o-ring. If anyone can tell me where to find out what type of o-ring I need, please speak up.

First photo shows a circle disk on the right hand side that has 2 holes in in. I use a pair of needle nose pliers jammed into the holes to turn the disk and remove it.

When an opening, I see there is a spring compressing the piston that is connected to the handle. When the disk is on, the spring pushes the piston against the handle which returns the hand grip to the open position by default.

I can remove the spring to expose the piston.

The center of the piston has a ring that is slightly smaller than the diameter of the opening.

There is actually a black o-ring around the ring. This o-ring blocks the flow of water through the handle. When the hand grip is open, the o-ring blocks the water and sends it through the aerator. When the hand grip is closed, the o-ring shifts a little as the piston is move and sends the water through the holes in the shower housing.

img_2989.jpg   img_2990.jpg   img_2991.jpg   img_2992.jpg   img_2993.jpg  

img_2994.jpg  
__________________
LeakingFaucet is offline  
 
Reply With Quote Quick reply to this message
Old 04-28-2014, 11:35 PM  
nealtw
Contractor
 
Join Date: Nov 2010
Location: vancouver, b.c.
Posts: 9,919
Liked 814 Times on 727 Posts
Likes Given: 1407

Default

It looks like it could be a kraus kpf-1602
They have a phone number, maybe you could send them a photo.


1-800-775-0703.

__________________
nealtw is offline  
 
Reply With Quote Quick reply to this message
Old 04-28-2014, 11:49 PM  
LeakingFaucet
Junior Member
 
Join Date: Apr 2014
Location: San Francisco, CA
Posts: 27
Liked 5 Times on 4 Posts

Default

It's definitely very similar but the rain shower section of the faucet is bell shaped for me, while it appears flat, disc shaped for the Kraus. Man, it's close though.

kpf-1602.jpg  
__________________
LeakingFaucet is offline  
 
Reply With Quote Quick reply to this message
Old 04-29-2014, 12:22 AM  
nealtw
Contractor
 
Join Date: Nov 2010
Location: vancouver, b.c.
Posts: 9,919
Liked 814 Times on 727 Posts
Likes Given: 1407

Default

I think most of the heads are interchangeable and perhaps if all else fails you might find a moen or delta head that fits. I would look at drilling the handle for ss screw.

__________________
nealtw is offline  
 
Reply With Quote Quick reply to this message
Old 04-29-2014, 08:27 AM  
LeakingFaucet
Junior Member
 
Join Date: Apr 2014
Location: San Francisco, CA
Posts: 27
Liked 5 Times on 4 Posts

Default

I've re-attached the handle. Turns out there's a screw with a hexagonal socket that can be used to fasten the handle to the nub that controls the faucet water flow.

Still not sure about the model of faucet or how to replace the o-ring.

__________________
LeakingFaucet is offline  
 
Reply With Quote Quick reply to this message
Old 04-29-2014, 08:54 AM  
kok328
Supporting Member
HRT_SUPPORTER.png
 
Join Date: Nov 2007
Location: Grand Blanc, MI
Posts: 2,185
Liked 105 Times on 92 Posts
Likes Given: 61

Default

If that was a true o-ring, take a chance on your local hardware store. Might cost about a $0.80 if it works.



__________________
kok328 is offline  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Help Identifying a Bath Faucet KenFlod Plumbing Forum 4 02-04-2013 03:44 PM
Help Identifying Bathtub Faucet perkins_j99 Plumbing Forum 5 01-08-2013 11:16 PM
Leaky faucet Jasmineluvsshane Plumbing Forum 2 05-17-2012 08:55 PM
Leaky Faucet colocowgirlinalaska Plumbing Forum 4 05-19-2011 10:56 PM
Leaky outside faucet Rike Plumbing Forum 2 05-14-2005 06:15 AM