DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Roofing and Siding > DIY rock roof




Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old 03-07-2006, 04:15 PM  
TxBuilder
HRT_LIFETIMESUPPORTER.png
 
TxBuilder's Avatar
 
Join Date: Feb 2005
Posts: 1,677
Liked 5 Times on 5 Posts
Likes Given: 4

Default DIY rock roof

We have a very slightly sloped garage roof that is the tar/rock combo.

It's leaking a few places here and there and overall it's not in good shape. Is replacing a tar/rock roof an easy DIY project or should I call in the experts on this one?



__________________
TxBuilder is offline  
 
Reply With Quote Quick reply to this message
Old 03-08-2006, 10:38 AM  
mickmar
Junior Member
 
Join Date: Nov 2005
Posts: 21
Default

TxBuilder, I would remove the old roof and install either rubber or roll roofing. Mick



__________________
mickmar is offline  
 
Reply With Quote Quick reply to this message
Old 03-08-2006, 10:45 AM  
TxBuilder
HRT_LIFETIMESUPPORTER.png
 
TxBuilder's Avatar
 
Join Date: Feb 2005
Posts: 1,677
Liked 5 Times on 5 Posts
Likes Given: 4

Default

Mick. Both of those are DIY projects? No expertise needed to install them?

__________________
TxBuilder is offline  
 
Reply With Quote Quick reply to this message
Old 03-08-2006, 06:53 PM  
Aceinstaller
Member
 
Join Date: Feb 2006
Posts: 49
Default

well, it depends on how much work you are willing to do, and how schooled you are in carpentry and roofing.

there will be the removal of the old roof.(which I have no idea how big or how thick the old roof is) removal will take a lot of hard labor and some dumpster coordination.(calling, scheduling, an placing dumpsters) After demo, you will need to frame the roof according to the local building codes required.(the local building inspector at the city hall might be able to guide you in the direction needed for requirements on lumber sizing and spacing when you purchase your permits) After framing and sheeting the roof to specs required, there will be flashing needed more than likely in some areas, then comes the fun part of laying the rubber or roll roofing.

all in all, I would call a company to complete a project of this magnitude.

if you need to ask if this is a diy project or not, that should indicate that you have very little knowledge of the scope of work. Although most of the job will pose no real problems, there are tricks of the trade involved in sealing a flatroof to ensure that these leaks don't reaccur any time soon.

If you really want to save money and you are good with a hammer, you could always demo and frame to code, then call a roofer to lay the new roof.

__________________
Aceinstaller is offline  
 
Reply With Quote Quick reply to this message
Old 03-09-2006, 09:54 AM  
mickmar
Junior Member
 
Join Date: Nov 2005
Posts: 21
Default

TxBuilder, for me it would be a DIY project because I worked for a roofer when I was much younger. You have to have some general knowledge about roofing to tackle a job like that. Probably be less expensive to have a pro do it if you don't know how. I should add that roofing is a very dirty, hot job. Good luck with whatever you decide on. Mick.

__________________
mickmar is offline  
 
Reply With Quote Quick reply to this message
Old 03-10-2006, 07:33 PM  
inspectorD
Housebroken
HRT_MODERATOR.png
 
inspectorD's Avatar
 
Join Date: Dec 2005
Location: Litchfield, CT
Posts: 3,986
Liked 103 Times on 88 Posts
Likes Given: 227

Default Yup!!

Backbreaker for sure. Dont invite you friends on this one either.Not if you want them to hang around anyway.
Im sure you know what i would say....Get a good roofer that specializes in rubber roofs. Longer life, less maintinence, easier repairs, warrantee!!

Then you get to focus on the next honeydooooo!!
InspectorD

__________________

Just My
Made in the

inspectorD is offline  
 
Reply With Quote Quick reply to this message
Old 03-11-2006, 02:04 PM  
TxBuilder
HRT_LIFETIMESUPPORTER.png
 
TxBuilder's Avatar
 
Join Date: Feb 2005
Posts: 1,677
Liked 5 Times on 5 Posts
Likes Given: 4

Default

Thanks for the advice. After doing more research and investigating the work load I am going to hire a professional.

__________________
TxBuilder is offline  
 
Reply With Quote Quick reply to this message
Old 03-12-2006, 09:01 PM  
broke
Member
 
Join Date: Mar 2006
Posts: 36
Default

I just read that doing a roof is an easy diy job.

__________________
broke is offline  
 
Reply With Quote Quick reply to this message
Old 03-12-2006, 11:52 PM  
Square Eye
Senior Member
 
Square Eye's Avatar
 
Join Date: Jan 2006
Posts: 1,273
Liked 4 Times on 4 Posts

Default

Yep, doing a roof is not very mentally taxing. AS LONG AS;

It has no less than a 2 1/2 / 12 pitch and no more than a 5/12 pitch

It has no valleys or changing pitches in the valleys

It's less than 12 ft from the ground to the fascia (gutter board)

It meets no walls or chimneys

The decking is in perfect condition

Standard materials are used

There are NO dormers

It's in straight runs
______________________________________

TX, the decision to get a pro on this one is smart. These low pitch roof with rock/tar in the mix can be nightmares even for the pros. First off, WTH do you cut it with? How do you get it off and out of the way so you can start over? I don't even have the torch outfit that these guys use. I have seen 3 different houses burnt to the ground because a torch can set a fire under the surface and not be seen for hours, meanwhile it smolders away and builds heat until it finds an adequate oxygen supply to create a roaring fire. CHECK YOUR CONTRACTOR'S LIABILITY INSURANCE BEFORE YOU LET HIM START!! This is very important.

Men don't pick roofing for a lifetime career, roofing picks you. My advice? Stay away from it. There's more to it than meets the eye.

Tom in KY, I hate roofing, I'm good at it,,BUT I HATE IT!!!

__________________

[URL="http://www.houserepairtalk.com/announcement.php?f=39&a=6"][size=3]The Ten Commandments of House Repair Talk[/size][/URL]



[URL="http://home.bellsouth.net/p/s/community.dll?ep=16&groupid=289528&ck="]Square Eye's home page[/URL]

Square Eye is offline  
 
Reply With Quote Quick reply to this message
Old 08-27-2006, 10:33 PM  
MONTY
Junior Member
 
Join Date: Aug 2006
Posts: 8
Default Replacing A Gravel Roof {yourself}

Quote:
Originally Posted by TxBuilder
We have a very slightly sloped garage roof that is the tar/rock combo.

It's leaking a few places here and there and overall it's not in good shape. Is replacing a tar/rock roof an easy DIY project or should I call in the experts on this one?
1 MAN 1 MAN
TEAR OFF:
1-TOOLS NEEDED:
1-FLAT SHOVEL LONG HANDLE.
2-WHEELBARROW {If Not Accessible to Haul Unit}
TECHNIQUE, TIME & LABOR:
1-SIMPLY START TEAR OFF BY HANGING YOUR SHOVEL OVER THE EDGE & LIFT UP ON EDGE METAL IN AN EFFORT TO UTILIZE EDGING AS A "HANDLE".
2-WHILE PULLING, WALK BACKWARDS & KEEP TUGGING. THE ROOF WILL TEAR. YOU EVENTUALLY CAN REGULATE THE SIZE AS TO WHAT YOU CAN HANDLE, OR {DRAG} TO THE PICK-UP TRUCK {BLANKET SIZE PIECES} WHICH WILL HAUL OFF 1,500 SF.AT A TIME PRETTY EASY.
3-ONCE ROOF IS BARE & DECK IS SHOWING. SIMPLY "POP" NAILS WITH SHOVEL. DRIVE THE 8d DECK NAILS AS NEEDED. REPLACE ROTTED AS NEEDED.
END OF SECTION
INSTALLATION
MATERIALS:
EDGE METALS: .................. 2-1/2" X 2-1/2" GALVANIZED.
SPRAY ON PRIMER.............. 1 "ONE} CAN WILL DO ABOUT 15 PIECES.
PRIMER ON TOP ROOF SIDE ONLY.
PEEL-N-SEAL ALUMINUM FOIL FACE "SELF ADHERING ROLL ROOF.
COVERAGE:....................... 1-ROLL "40" X 33' = 100 SF W/4" LAP.
ADHERE STRAIGHT TO DECK. START AT BOTTOM OF SLOPE.
RENTAL:........................... 1-LINOLEUM ROLLER FOR WEIGHT ON SEAMS.
SLOPE.............................. DECREASES VULNERABILITY OF SEAMS.
EDGE METALS/HOLDING POWER:
NAIL THROUGH METAL AFTER PLACING OVER "RUBBER" ROOF.
LAP JOINTS X 2". NAIL ON NO LESS THAN 12" INTERVALS DUE TO MOVEMENT DURING WEATHER EXTREMES.
CUT 6" STRIPS & STRIP IN METALS TO WATERPROOF. SEAL DOWN WITH FEET.
WALLS / 90* TIE-IN AREAS:
BY NOW, YOU CAN PRIME AN AREA & SEAL ROOF TO WORK ON ALL MARRIAGES & TERMINATED AREAS.
BRICK WALL OR STUCCO OR HARD TO ACCESS TIE-INS:
USE NP1 CAULKING BY SONNEBORN {COLOR MATCH}
ASTM: WONT PEEL FROM SURFACE
1 MAN CAN TAER OFF, CARRY UP A LADDER & REPLACE AVG. 12-15 SQ. "100 SF" PER DAY.
*SELF ADHERING
*NO TORCH, FUMES OR TAR NEEDED.
*WONT BLOW OFF.
*SIMPLE STEPS TO SAVING MONEY.
*1 JOB & YOU FEEL LIKE AN "INSTANT ROOFER"
M A GRUNT SIMPLE SPECS
*CAN BE USED AS A PIGGYBACK BASE SHEET FOR NEXT HAIL STORM WITH SAME MATERIALS & NO DEMO.
*FOIL FACING REFLECTS 85% UV RAYS & RADIANT HEAT TRANSFER.

END OF SECTION
PAY YOURSELF A FEW CAR PAYMENTS YOU WOULD HAVE PAID A GUY WITH 2 LABORERS TO DO WHILE HE RODE AROUND WAITING TO COLLECT

SPECIFIED BY:
MONTY GEE SR.
FORT WORTH, TEXAS
40 YEARS IN ARENA
FLATROOFEXPERT@AOL.COM


__________________
MONTY is offline  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Raising Roof Pitch JulieC Roofing and Siding 14 03-04-2012 05:22 PM
Flat roof on block of flats - rebuild advice Martinr Roofing and Siding 3 01-16-2009 09:26 AM
Raising the roof NoviceBuilder Bricks, Masonry and Concrete 1 01-14-2009 11:31 AM
Patio roof to house attachment question mobilemike Roofing and Siding 2 09-23-2008 07:31 AM
Help with ventilation of Gambrel Roof weng19 Roofing and Siding 5 03-04-2008 06:40 PM