DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Roofing and Siding > Getting rain water behind siding




Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old 10-23-2011, 10:02 PM  
sas09
Junior Member
 
Join Date: Oct 2011
Posts: 2
Default Getting rain water behind siding

Recently had vinal siding installed, J channel at bottom is about even with top of lower trim board and I think is allowing rain water to run behind that board (can see it dripping) Seems that the J channel should have been lower. Can I do this and how do I extend the channels on the sides? See pic.



cellar-floor-project-060.jpg  
__________________
sas09 is offline  
 
Reply With Quote Quick reply to this message
Old 10-24-2011, 02:37 AM  
nealtw
Contractor
 
Join Date: Nov 2010
Location: vancouver, b.c.
Posts: 9,495
Liked 756 Times on 675 Posts
Likes Given: 1310

Default

Yes you should have had a Z flashing on top of the board and behind the paper behind the siding. You can expose the nails at the top of the first panel with a zipper tool and remove that panel to do this, you will need to cut some off the bottom of that panel when re-installing it so that it isn't to tight.
Zipper tool is a cheep little tool sold where they sell siding.



__________________
nealtw is online now  
 
Reply With Quote Quick reply to this message
Old 10-24-2011, 06:21 PM  
sas09
Junior Member
 
Join Date: Oct 2011
Posts: 2
Default z flashing?

What is a Z flashing and how does it help? Also, not sure what you mean by cutting the botton panel.

__________________
sas09 is offline  
 
Reply With Quote Quick reply to this message
Old 10-24-2011, 10:18 PM  
nealtw
Contractor
 
Join Date: Nov 2010
Location: vancouver, b.c.
Posts: 9,495
Liked 756 Times on 675 Posts
Likes Given: 1310

Default

Google Image Result for http://www.hinkleymetalproducts.com/z_04.gif
__________________
nealtw is online now  
 
Reply With Quote Quick reply to this message
Old 10-24-2011, 10:21 PM  
nealtw
Contractor
 
Join Date: Nov 2010
Location: vancouver, b.c.
Posts: 9,495
Liked 756 Times on 675 Posts
Likes Given: 1310

Default

It looks to me that you have to remove some siding to install flashing and then the siding will be to big to replace.

__________________
nealtw is online now  
 
Reply With Quote Quick reply to this message
Old 10-27-2011, 08:37 AM  
joecaption
Senior Member
 
Join Date: Jan 2011
Location: Hartfield VA, VA
Posts: 1,361
Liked 38 Times on 33 Posts
Likes Given: 2

Default

I personaly never would have installed the siding the way it was done.
All the old wood has been left exposed. I would have remove it and used vinyl outside corners and ran the siding from the bottom using starter strip.
You need to add that Z moulding or another way is to use coil stock and wrap that bottom area and run it at least 3" up behind the siding.



__________________
joecaption is offline  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Roof leak problem with new roof muty Introductions 5 09-03-2013 06:15 PM
Water Damaged Exterior Siding dcsmith37 Roofing and Siding 4 06-04-2011 06:04 PM
Water Through Siding? GeoSeif Roofing and Siding 8 03-13-2011 02:01 PM
Rain water dripping into microwave? Foodcubes HVAC 14 01-17-2011 05:27 PM