DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Roofing and Siding > How to properly vent lower roofs?





Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old 04-24-2013, 10:12 AM  
o2284200
Member
 
Join Date: Oct 2012
Location: , South Florida
Posts: 92
Liked 4 Times on 3 Posts

Default How to properly vent lower roofs?

In the middle of 2nd day of re-roof...

The 2 lower roofs, which share a small attic crawl space have what appears to be ample intake soffits on the front & sides but I'm trying to figure out the best way to vent outward from the near top without ruining aesthetics.

I've added 2 goose-necks to the back of the upper roof but I really don't think that will look good in the front lower roofs. I'm considered trying to put some sort of "gable vent" on one or both ends but your thoughts & opinions would be greatly appreciated!

FWIW, this is stucco over concrete block in Dade county, Florida within 1/2 mile of ocean.

THANKS!





__________________

Last edited by o2284200; 04-24-2013 at 10:15 AM.
o2284200 is offline  
 
Reply With Quote Quick reply to this message
Old 04-24-2013, 10:49 AM  
nealtw
Senior Member
 
Join Date: Nov 2010
Location: vancouver, b.c.
Posts: 7,741
Liked 541 Times on 490 Posts
Likes Given: 1000

Default

The vents in the lower two photos are in the overhang on the sides, in most cases there isn't access to the attic from there unless someone cut into structure. In some cases the roof has been strapped sideways with 1x4 or 2x4 and then you will have some air movement there.



__________________
nealtw is offline  
 
Reply With Quote Quick reply to this message
Old 04-24-2013, 11:23 AM  
o2284200
Member
 
Join Date: Oct 2012
Location: , South Florida
Posts: 92
Liked 4 Times on 3 Posts

Default

Thanks, there are intake soffit vents in both lower overhangs on the front too.
And there's a crawl space that gives access to both lower overhang attics.

__________________

Last edited by o2284200; 04-24-2013 at 11:29 AM.
o2284200 is offline  
 
Reply With Quote Quick reply to this message
Old 04-24-2013, 11:56 AM  
nealtw
Senior Member
 
Join Date: Nov 2010
Location: vancouver, b.c.
Posts: 7,741
Liked 541 Times on 490 Posts
Likes Given: 1000

Default

Stick your head up in the attic and see if there are openings from the attic to where the vents are on the sides, if not look to see if the roof sheeting is nailed to the rafters or is there strapping between the rafters and the sheeting, if the answer to both is no then you need more venting, if the answer is yes to one or both, you likely are fine.

__________________
nealtw is offline  
 
Reply With Quote Quick reply to this message
Old 04-24-2013, 12:38 PM  
oldognewtrick
Moderator
HRT_MODERATOR.png
 
oldognewtrick's Avatar
 
Join Date: Jul 2009
Location: Nashville, TN
Posts: 3,777
Liked 277 Times on 232 Posts
Likes Given: 89

Default

At the spot where the lower roof runs into the wall you should use a vent like Smart Vent that allows for head wall exhaust. Then the counter flashing should be fabricated go cover the Smart Vent.

__________________
oldognewtrick is online now  
 
Reply With Quote Quick reply to this message
Old 04-24-2013, 12:44 PM  
CallMeVilla
Senior Member
 
CallMeVilla's Avatar
 
Join Date: Feb 2010
Location: San Diego
Posts: 1,061
Liked 267 Times on 217 Posts
Likes Given: 105

Default

Heck! OldDog beat me to it ... Smart Vent has an application which applies to this situation. You might call it a "shed roof to wall" application because you have vents at the bottom but not at the top.

Go to their site: http://www.dciproducts.com/html/smartvent.htm

Get 'er done! Do it right!

__________________
CallMeVilla is offline  
 
Reply With Quote Quick reply to this message
Old 04-24-2013, 01:17 PM  
o2284200
Member
 
Join Date: Oct 2012
Location: , South Florida
Posts: 92
Liked 4 Times on 3 Posts

Default

Here's a shot in the attic looking at the lower right side of house or the 3rd pic from above. I can see the openings on this side but I was not able to get near the other side so I can only assume it;s the same set up.

__________________

Last edited by o2284200; 04-24-2013 at 02:51 PM.
o2284200 is offline  
 
Reply With Quote Quick reply to this message
Old 04-24-2013, 02:39 PM  
oldognewtrick
Moderator
HRT_MODERATOR.png
 
oldognewtrick's Avatar
 
Join Date: Jul 2009
Location: Nashville, TN
Posts: 3,777
Liked 277 Times on 232 Posts
Likes Given: 89

Default

You should close off the side vents and have a continues vent strip along the eave for air intake and a continous vent at the wall for exhaust. The vents along the side will allow the vent system to short cycle.

__________________
oldognewtrick is online now  
 
Reply With Quote Quick reply to this message
Old 04-24-2013, 03:11 PM  
o2284200
Member
 
Join Date: Oct 2012
Location: , South Florida
Posts: 92
Liked 4 Times on 3 Posts

Default

Quote:
Originally Posted by oldognewtrick View Post
At the spot where the lower roof runs into the wall you should use a vent like Smart Vent that allows for head wall exhaust. Then the counter flashing should be fabricated go cover the Smart Vent.
Quote:
Originally Posted by CallMeVilla View Post
Heck! OldDog beat me to it ... Smart Vent has an application which applies to this situation. You might call it a "shed roof to wall" application because you have vents at the bottom but not at the top.

Go to their site: http://www.dciproducts.com/html/smartvent.htm

Get 'er done! Do it right!
Thanks, that looks awesome, would you go all the way across the top on each side of the lower roofs?

Also was looking at O'Hagins...
Has anyone had experience with their "Vents for Tile Roof Applications" http://www.ohagin.com/products_tile.asp ???
__________________

Last edited by o2284200; 04-24-2013 at 06:41 PM.
o2284200 is offline  
 
Reply With Quote Quick reply to this message
Old 04-24-2013, 05:30 PM  
CallMeVilla
Senior Member
 
CallMeVilla's Avatar
 
Join Date: Feb 2010
Location: San Diego
Posts: 1,061
Liked 267 Times on 217 Posts
Likes Given: 105

Default

The application requires a gap at the top. You can cut the sheathing to create this gap and apply the Smart Vent all the way across. The flashing will have to be determined based on your wall structure. The couter-flashing makes perfect sense.

http://www.dciproducts.com/html/shedroof.htm#offwall





__________________
CallMeVilla is offline  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Cleaning lower sprayer Blue Jay General Appliance Discussion 3 12-19-2012 04:33 PM
lower heat loss recessed lights. coach606 Electrical and Wiring 9 11-28-2012 02:42 PM
GE Dryer (model DBXR463ED2WW) does not cycle to lower temp Back40 General Appliance Discussion 3 11-22-2011 06:04 AM
kelvinator refrigerator, freezer working, lower section not psalm3401 Refrigerators 2 04-24-2011 02:23 PM
Flat roofs??? starrider Carpentry and Woodworking 10 08-13-2006 06:28 PM