DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > General Home Improvement Discussion > Countertops too short




Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old 08-07-2011, 04:49 PM  
Ourladykaty
Junior Member
 
Join Date: Aug 2011
Location: Grover Beach, CA
Posts: 3
Default Countertops too short

I recently renovated my kitchen and installed tile countertops. I planned to do the tile myself, so I talked to my contractor and he agreed to install the subtop for me, so all I would have to do was lay the tile in. Once I completed the install, I realized that the subtop had been measured to align with the face of the cabinets, not the face of the drawers. The drawers stick out from under the tile by about a half inch when closed. Is there a way to fix this without tearing out the entire installation and starting from scratch?



side.jpg   top.jpg  
__________________
Ourladykaty is offline  
 
Reply With Quote Quick reply to this message
Old 08-07-2011, 10:58 PM  
nealtw
Contractor
 
Join Date: Nov 2010
Location: vancouver, b.c.
Posts: 10,328
Liked 858 Times on 766 Posts
Likes Given: 1485

Default

Here I thought I was the only one that made this mistake. Knock off the tile on the face and add a peice of 1x2 and retile the end.



__________________
nealtw is online now  
 
Reply With Quote Quick reply to this message
Old 08-08-2011, 09:15 AM  
TxBuilder
HRT_LIFETIMESUPPORTER.png
 
TxBuilder's Avatar
 
Join Date: Feb 2005
Posts: 1,677
Liked 5 Times on 5 Posts
Likes Given: 4

Default

Neal makes good sense here. I would knock off the front as well. You're going to have to mess some of it up, this is where I would start.

__________________
TxBuilder is offline  
 
Reply With Quote Quick reply to this message
Old 08-09-2011, 01:11 PM  
Ourladykaty
Junior Member
 
Join Date: Aug 2011
Location: Grover Beach, CA
Posts: 3
Default

Thanks for the responses! I found another option - installing a wood cap instead of tile. Do you guys think nailing into the plywood subtop would be strong enough to support that kind of edging?

__________________
Ourladykaty is offline  
 
Reply With Quote Quick reply to this message
Old 08-09-2011, 01:34 PM  
oldognewtrick
Moderator
HRT_MODERATOR.png
 
oldognewtrick's Avatar
 
Join Date: Jul 2009
Location: Nashville, TN
Posts: 5,459
Liked 464 Times on 386 Posts
Likes Given: 147

Default

I would screw and glue the wood trim in place with some construction adhesive, and make sure it extends out past the drawer facing. You can find screws with very small heads on them, sink them beneath the surface, fill the holes and apply finish. If you paint the wood the color of the tile it won't look so much like an add-on.

__________________
oldognewtrick is offline  
 
Reply With Quote Quick reply to this message
Old 08-09-2011, 01:37 PM  
Ourladykaty
Junior Member
 
Join Date: Aug 2011
Location: Grover Beach, CA
Posts: 3
Default

Excellent, oldog/newtrick. Thanks!



__________________
Ourladykaty is offline  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Chimney bricks spalling. Req opinions on short & long term repairs. golem Bricks, Masonry and Concrete 6 11-13-2010 07:17 AM
Short-cutting the duct/vent JulieC HVAC 0 05-26-2010 09:00 AM
My New Bathroom Sink Drain Is Too Short Lilly General Home Improvement Discussion 5 06-27-2008 02:44 PM
I caused a short in one room - now what? taychas Electrical and Wiring 2 11-08-2006 03:03 PM
1 wire short wheelman HVAC 2 10-22-2006 11:09 PM