DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > General Home Improvement Discussion > Drill Bit Problem Driving Me Crazy 😳




Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old 06-05-2013, 07:50 AM  
luckywinks
Junior Member
 
Join Date: May 2013
Posts: 15
Liked 2 Times on 2 Posts

Default

I have a new Ryobi drill and bought a new Bosch concrete masonry drill bit set to drill holes into the wall of the exterior of my lath and plaster built garage. I notice from time to time when using the drill that the bits simply do not seat properly and they get stuck in the surface on this project and other easy jobs as well and the drill simply powers on. I've tightened the chuck as far as I can and it still doesn't hold the bit well enough. Is this normal, what's happening and why does this occur? It's frustrating and doesn't seem satisfactory performance to me.
Please help.



__________________

Last edited by luckywinks; 06-05-2013 at 07:52 AM.
luckywinks is offline  
 
Reply With Quote Quick reply to this message
Old 06-05-2013, 08:04 AM  
bud16415
Fixer Upper
 
bud16415's Avatar
 
Join Date: Feb 2013
Location: Erie Pa, Pa
Posts: 1,215
Liked 352 Times on 282 Posts
Likes Given: 113

Default

Do you have a drill with a key chuck or keyless? In both cases sometimes dust like you get from old lath plaster will work its way into the chuck and jam the jaws making them feel like they are tight when not. Take the bit out and hold the ring and run the drill forward and reverse a few times spinning the jaws in and out to loosen them up. You can also spray some light oil like WD40 in there when you do this to keep things working.

The reason I asked about keyless is they are nice and fast but IMO don’t get as tight as a keyed chuck. With a key I think you get a better feel when the jaws are sticking.



__________________
bud16415 is offline  
 
Reply With Quote Quick reply to this message
Old 06-06-2013, 08:13 AM  
luckywinks
Junior Member
 
Join Date: May 2013
Posts: 15
Liked 2 Times on 2 Posts

Default

Thanks for the info Bud!

It's a keyless chuck that I simply hand tighten. This problem occured just as I began to start to drill. I've used the drill mostly for a Phillips screw bit and not to drill. I'm really surprised by this so will get it cleaned up and see how it goes for my next project.

__________________
luckywinks is offline  
 
Reply With Quote Quick reply to this message
Old 06-06-2013, 08:43 AM  
nealtw
Contractor
 
Join Date: Nov 2010
Location: vancouver, b.c.
Posts: 10,221
Liked 838 Times on 749 Posts
Likes Given: 1454

Default

This is a problem with keyless chucks, some drills may have better chucks but we put up with this. It is made worse with a masonary bit as it has lumps at the tip. When you hit a cavity or something hard it tends to lock up the drill bit making it slip. The other side is if you have a powerfull drill that holds the bit really good and the bit locks up in the hole, the drill will take you for a ride, hard on the wrist.

__________________
nealtw is online now  
 
Reply With Quote Quick reply to this message
Old 06-06-2013, 06:04 PM  
elbo
 
Join Date: Nov 2011
Location: , florida
Posts: 76
Liked 20 Times on 20 Posts
Likes Given: 17

Default

If you would start the hole with as small a bit you can get , drilling all the way through, then follow up with suceedingly larger drill bits until you reach the size you need, you will have more sucess

__________________
elbo is offline  
 
Reply With Quote Quick reply to this message
Old 06-07-2013, 06:20 AM  
mabloodhound
Restoration & Renovations
 
Join Date: Jun 2008
Location: Halifax, MA
Posts: 39
Liked 3 Times on 2 Posts

Default

You mentioned that the "drill bits do not seat properly" Not sure what you mean but if you are pushing the drill bit all the way into the chuck until it hits bottom, this could be your problem. Do not allow the bit to hit the bottom when you tighten the chuck. Doing so sometimes prevents the chuck from getting fully tightened. Just pull it back a little off the bottom and then tighten.

Dave Mason

__________________
mabloodhound is offline  
2
People Like This 
Reply With Quote Quick reply to this message
Old 06-07-2013, 10:20 AM  
luckywinks
Junior Member
 
Join Date: May 2013
Posts: 15
Liked 2 Times on 2 Posts

Default

"Seating" or inserting the drill bit, same thing. That's a term I saw used elsewhere. Sorry for the confusion. All of this advice is helpful and much appreciated. I did start with a smaller bit and as it turned out I needed to work up to a larger size anyhow so it worked out. So now I understand in the future. I'm not so keen on having the drill flip around in my hands so I can live with some slippage from time to time.

Has anyone tried this new adhesive product called Instantbond! It's a concrete bonding agent ( among other surfaces) , good for attaching screws to masonry surfaces. I bought some for future projects to attach twine and screws to support vine plants along a cinderblock wall. I saw a video on YouTube and it looked pretty useful. http://www.instantbond.com/

Have a happy DIY weekend everyone!



__________________
luckywinks is offline  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
bathroom leaks driving me insane mayhem69 General Home Improvement Discussion 13 09-24-2012 07:11 PM
crazy fan... acproblem HVAC 5 03-09-2010 09:41 AM
Those Crazy Contractors Billvila General Chit-Chat 11 10-03-2009 08:49 AM
going crazy tobproud Introductions 1 05-28-2006 07:54 PM
HELP! Outside noise is driving me crazy! goofycat Introductions 1 04-12-2006 05:35 PM