DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > General Home Improvement Discussion > Exterior Window Trim Help




Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old 11-06-2012, 11:26 AM  
drewdin
Junior Member
 
Join Date: Aug 2012
Posts: 389
Liked 23 Times on 21 Posts
Likes Given: 77

Default Exterior Window Trim Help

Hi Guys,

I got three windows side by side by side, one window is 47" wide and the next two are 60" wide. The gaps between the windows are different also, they are 3-3/4, 6-1/2 and 2-3/4.

My problem with these windows is that there is a 1/4" space between the window and the rough opening on the sides and tops of each window, right to the outside. These windows were installed by the previous owner, they are replacement windows only held in by one screw on each side, they are loose and feel as if they are going to fall out.

I will provide some pictures later today but my question is what is the best way to fix them? I have done a bunch of research on the internet and this is what i found to do, I have listed those steps below. If anyone has any advise, tips or tricks I would greatly appreciate it!

Steps:

  1. Remove windows, properly flash the rough opening and verify its level.
  2. Install exterior window trim that shrinks the rough opening by 1/2" all around the window
  3. Push window up against the new trim, center the window with shims and use two exterior screws on each side of the window to secure it.
  4. Use window and door foam to seal window from inside along with caulking on the seam of the window and wood on the outside.
Thanks!


__________________
drewdin is offline  
 
Reply With Quote Quick reply to this message
Old 11-06-2012, 11:53 AM  
nealtw
Senior Member
 
Join Date: Nov 2010
Location: vancouver, b.c.
Posts: 8,951
Liked 682 Times on 611 Posts
Likes Given: 1202

Default

Not sure how you get 3 dividers between three windows. Windows are usually 1/2" smaller than the opening. this gives you room to level and plumb them. They should be shimmed so they center in the hole and screws on each side should go where there are shims.
Double check the distance between windows so they measure the same top and bottom to make trimming easier. Make sure the tops and bottoms all line up if they are all the same heights. Foam around the inside and caulking the outside will be about all you can do withan older house.



__________________
nealtw is offline  
 
Reply With Quote Quick reply to this message
Old 11-06-2012, 11:58 AM  
drewdin
Junior Member
 
Join Date: Aug 2012
Posts: 389
Liked 23 Times on 21 Posts
Likes Given: 77

Default

When the framing was done for these windows, it was not done properly. I post some pics later tonight and your jaw will drop, unfortunately when i bought the house this stuff was covered up. there is about 1/4" spacing and less in some areas, around the windows.

It was a deck that was made into a sunroom. I'm doing my best to make what I got secure without ripping it down and rebuilding it. I'm sure the pictures will give you much more insight.

__________________
drewdin is offline  
 
Reply With Quote Quick reply to this message
Old 11-06-2012, 12:18 PM  
drewdin
Junior Member
 
Join Date: Aug 2012
Posts: 389
Liked 23 Times on 21 Posts
Likes Given: 77

Default

Also, when nailing in the exterior trim, how do i sink the nails into the wood to hide them, i dont want to use finish nails. What do you recommend? Thanks

__________________
drewdin is offline  
 
Reply With Quote Quick reply to this message
Old 11-06-2012, 12:44 PM  
nealtw
Senior Member
 
Join Date: Nov 2010
Location: vancouver, b.c.
Posts: 8,951
Liked 682 Times on 611 Posts
Likes Given: 1202

Default

Hot dipped galvanized is the standard, why wouldn't you use finishing nails? They hold fine.

__________________
nealtw is offline  
 
Reply With Quote Quick reply to this message
Old 11-06-2012, 01:23 PM  
drewdin
Junior Member
 
Join Date: Aug 2012
Posts: 389
Liked 23 Times on 21 Posts
Likes Given: 77

Default

I thought that you needed to have it secure but again, im a rookie and have no clue. I thought that finish nails would not hold it correctly

__________________
drewdin is offline  
 
Reply With Quote Quick reply to this message
Old 11-06-2012, 01:31 PM  
nealtw
Senior Member
 
Join Date: Nov 2010
Location: vancouver, b.c.
Posts: 8,951
Liked 682 Times on 611 Posts
Likes Given: 1202

Default

They work fine.

__________________
nealtw is offline  
 
Reply With Quote Quick reply to this message
Old 11-07-2012, 04:00 PM  
RickMerlander
Junior Member
 
Join Date: Dec 2011
Location: Honolulu, Molokai Hawaii
Posts: 22
Liked 2 Times on 2 Posts
Likes Given: 2

Default How about stainless steel nails?

You can also use stainless steel either finishing nails or thin siding nails. These will never rust. Then take a nails set and pound the nail head in slightly below the wood surface and fill the resulting shallow hole with a patching compound like Ready Patch. Prime over this. Then paint.



__________________

Rick Merlander
Molokai Hawaii

RickMerlander is offline  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Rot on trim/underside of bay window esk Windows and Doors 3 07-13-2011 04:14 PM
exterior 1x4 trim TheMcs Carpentry and Woodworking 8 02-19-2011 06:33 AM
PVC Exterior Trim and Caulking Krystene Windows and Doors 1 02-03-2010 01:42 PM
5/4 Cedar vs. 5/4 PVC For Exterior Window Trim Larry69 Carpentry and Woodworking 1 08-25-2009 02:44 PM
exterior trim berbertWinslow Introductions 1 05-29-2007 09:23 PM