DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > General Home Improvement Discussion > Kitchen Wall Cabinets




Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old 06-16-2011, 07:27 AM  
Hayward
Junior Member
 
Join Date: Jun 2011
Location: Baltimore, MD
Posts: 1
Default Kitchen Wall Cabinets

Hello,

My contractor is installing my upper cabinets and says they should be flush against the ceiling with no trim between the cabinet and the ceiling. Looks awful to me. The doors go right to the top of the cabinet too so are only about 1/2 inch from the ceiling. Shouldn't there be some sort of trim up there to finish the upper edge where the cabinet meets the ceiling? If I move the cabinets down to allow more space for trim, then there's no place on the cabinet frame to nail in the trim. It would have to be nailed to the ceiling only.

Thanks for any help.



__________________
Hayward is offline  
 
Reply With Quote Quick reply to this message
Old 06-16-2011, 12:58 PM  
TxBuilder
HRT_LIFETIMESUPPORTER.png
 
TxBuilder's Avatar
 
Join Date: Feb 2005
Posts: 1,677
Liked 5 Times on 5 Posts
Likes Given: 4

Default

It sounds like those cabinets were built with no intention of using a trim at the top. Do you have some pictures of the gap?



__________________
TxBuilder is offline  
 
Reply With Quote Quick reply to this message
Old 06-16-2011, 04:52 PM  
oldognewtrick
Moderator
HRT_MODERATOR.png
 
oldognewtrick's Avatar
 
Join Date: Jul 2009
Location: Nashville, TN
Posts: 5,412
Liked 459 Times on 382 Posts
Likes Given: 145

Default

Quote:
Originally Posted by TxBuilder View Post
It sounds like those cabinets were built with no intention of using a trim at the top. Do you have some pictures of the gap?
Also, what is the ceiling heigth? How much space between the bottom of the cabinets and the top of the counter? Pics always help.
__________________
oldognewtrick is offline  
 
Reply With Quote Quick reply to this message
Old 06-18-2011, 07:46 AM  
joecaption
Senior Member
 
Join Date: Jan 2011
Location: Hartfield VA, VA
Posts: 1,361
Liked 38 Times on 33 Posts
Likes Given: 2

Default

Kitchen Cabinets
They could have simply added a strip of 3/4" or even a full 2 X 4 at the tops of the cabinets set flush with the front of the rails and attached it from inside the cabinets through the rails, then just line up the trim or crown moulding with the very top of the cabinets so the nailers do not show but would give some added holding power to the nails.
__________________
joecaption is offline  
 
Reply With Quote Quick reply to this message
Old 07-15-2011, 04:09 AM  
jack12
Junior Member
 
Join Date: Jul 2011
Location: Abbott, Texas
Posts: 2
Default

I think the strip of 3*4 will be best. Cabinets plays vital role in kitchen thus best fitting is very necessary

__________________

[URL="http://www.friendlycontractor.com/"]Kitchen Remodel[/URL]

jack12 is offline  
 
Reply With Quote Quick reply to this message
Old 07-23-2011, 11:28 PM  
RocLok
RocLok Master
 
Join Date: Jul 2011
Location: Beaverton, Oregon
Posts: 43
Default

Depending on the height of the upper cabinets, you may or may not be able to lower the cabinets without affecting the distance between the upper and lower cabinets in a negative way. If you decrease the distance between the cabinets too much it will look strange and be difficult to use all of the counter space.

So given that you can lower then, installation of crown molding above the doors to the ceiling looks great and adds a lot. In my last kitchen we left enough room for the crown molding plus 1” so we were able to install a rope light above the cabinets, it made a nice effect of light across the ceiling above the crown molding and cabinets. Crown molding is not very heavy so the supports for the molding do not need to be huge. We used pieces of 2X4 and cut out a section so it went over the upper edge of the cabinet, this allowed us to mount the molding to the 2X4 and the lower edge of the molding was flush with the upper edge of the door.

Now the reality is that the installation of the molding was complicated especially because of the type of crown we chose, it added about $1500-2,000 to the cost. There were several corners and things that added to the complexity, but it is not inexpensive if you pay someone to do it for you.

Like mentioned before a picture is worth a thousand words, attach one and we can help more.

-Ryan



__________________

Ex Realtor, house flipper, remodelor and now building a vintage truck, making friends and fixing my house.

Ever Lock Yourself out? [url]www.RocLok.com[/url]

Building a vintage 39 1.5 Ton Truck[URL="http://www.1939Cummins.Info"]http://www.1939Cummins.Info[/URL]

RocLok is offline  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Kitchen Cabinets kappadoce General Home Improvement Discussion 2 04-18-2011 07:35 AM
RTA kitchen cabinets? superjedi Decorating and Design 15 10-31-2010 03:35 AM
Kitchen Cabinets shan2themax General Home Improvement Discussion 11 03-16-2010 03:02 PM
Kitchen wall cabinets without base cabinets?? Christian General Home Improvement Discussion 7 03-15-2010 03:39 PM
kitchen cabinets rocky.disalva Flooring 0 07-04-2008 04:00 AM