DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > General Home Improvement Discussion > Vent dryer out basement window?





Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old 12-14-2009, 12:12 PM  
nrv1013
Junior Member
 
Join Date: Dec 2009
Posts: 1
Default Vent dryer out basement window?

I recently moved into a townhouse where the dryer is in the basement. It's currently venting under the stairs into a can with water in it. The home inspector said this was unusual but was okay. However, during the summer months I found a large amount of moisture ending up in my basement. I was dumping a 40 pint dehumidifier every other day. It's not so bad now that its winter time. I'm only emptying the dehumidifer about every week or week and a half. But I would like to get the dryer venting out the basement window.

The "laundry room" is positioned under the stairs against a wall with my neighbor's townhouse on the other side. The basement window out the back of the house is about 12 feet away with a small drywall wall inbetween. The window is in the small unfinished portion of the basement in an enclosed space so I don't care about blocking the light from the window or entirely replacing the glass with plywood or some other material. The window view is blocked from the outside by a propane tank anyway. The hot water heater is in the path but I believe there is enough room to go over/around it along the unfinished ceiling.

Is this too far for the vent duct to run? Or will I need some sort of booster for the ventilation? Also, do I need to put some sort of lint trap in the run somewhere? I'm also curious if there are any codes (PA) that I should look into as far as what I'm allowed to hook up.



__________________
nrv1013 is offline  
 
Reply With Quote Quick reply to this message
Old 12-15-2009, 03:54 PM  
SendEveryone
Junior Member
 
Join Date: Dec 2009
Posts: 4
Default

Lows has a 4" Diam.x20 foot flexible dryer vent Hose that you can run from your dryer to a panel in the window and a hood that you could glue in place out the windows.

Lambro Industries 4" x 20' LamaFlex Connector
Lambro Industries 4" White Replacement Hood

The vent duct won’t be too long to run; you won’t need a booster for the ventilation or a lint trap (if you do, put it in later - a small in line-fan will work). I put one of these in for my neighbor and it works fine, she is happy with it. As far as a permit, that’s up to you and your inspector.



__________________
SendEveryone is offline  
 
Reply With Quote Quick reply to this message
Old 12-17-2009, 04:32 AM  
Superpack
Member
 
Join Date: Oct 2009
Posts: 98
Default

You cut the hd sells sheets (paper backing and about 1/2" thick they come in 2'x 4’) the size of the window and tape them up. You may see thicker sheets that you can glide in from the outer surface against the glass. That cold is running along the ground and dropping into the window area especially is a pit on the outside.

Regards,

__________________
Superpack is offline  
 
Reply With Quote Quick reply to this message
Old 12-17-2009, 10:39 PM  
GBR
Senior Member
 
Join Date: Mar 2009
Posts: 337
Liked 18 Times on 17 Posts
Likes Given: 9

Default

Your home inspector may be a few years behind the times. Metal flex duct (rated and stamped) for 8' maximum length.

S.E., you are liable for your neighbor in case of fire......

http://www.hcpdc.com/pdf/Dryer%20Vent%20Requirements.pdf

Powered by Google Docs
Be safe, Gary

__________________
GBR is offline  
 
Reply With Quote Quick reply to this message
Old 12-18-2009, 01:05 PM  
Mikeman
Junior Member
 
Join Date: Dec 2009
Posts: 20
Default

Suggest checking with the association for your complex as to what is approved in terms of modifications to the outside wall of your townhouse. If the original plans had a laundry area that was located where it would be too far to vent properly to the outside you may be able to get some consideration for alternative approaches.

In your situation you not only have a long run but also 3-4 90 degree bends which will also restrict outward flow from the dryer. Venting to the basement window is going to be easiest and most effective if it will not cause problems with the owners' association. It will be much easier to periodically clean out the vent and keep the air flowing from the dryer and reduce your cost to operate it.



__________________
Mikeman is offline  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Vent through glass block window? Salterian Bricks, Masonry and Concrete 3 10-01-2009 08:01 PM
Dryer Vent Debacle WishIKnew General Home Improvement Discussion 12 02-27-2009 04:16 PM
Removed basement stairs - put in floor for washer and dryer capslock Flooring 4 04-02-2008 02:39 PM
Is it OK to tap into Dryer Vent? Duncanrinaldo General Appliance Discussion 3 09-07-2007 06:15 AM
Dryer vent Blair1955 General Appliance Discussion 9 05-06-2007 03:53 PM