DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Carpentry and Woodworking > Crown Moulding Installation




Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old 05-30-2007, 09:28 PM  
oakley408
Junior Member
 
Join Date: Apr 2007
Posts: 4
Default Crown Moulding Installation

Trim-out is not being done on the new home we are building. The GC is using a reasonably large crown moulding...about 6" wide. There is an outside corner where the entry foyer joins the greatroom. And it is on a vaulted ceiling surface. I have seen decorative blocks used on inside corners which "kills" the crown moulding. But I've never seen crown moulding joined on a sloping vaulted surface on an outside corner...thus the use of a decorative type block here is difficult to conceive.

Any ideas? Suggestions of "outsided" corner decorative blocks that might be available? Recommended websites?


Thanks

oakley408



__________________

Last edited by oakley408; 05-30-2007 at 09:30 PM.
oakley408 is offline  
 
Reply With Quote Quick reply to this message
Old 05-31-2007, 10:40 AM  
glennjanie
Senior Member
 
Join Date: Mar 2006
Posts: 2,990
Liked 2 Times on 2 Posts

Send a message via AIM to glennjanie
Default

Hello Oakley:
You could consider an "L" shaped block laid onto the wall and join the crown moulding to each leg of the L. Don't forget there are some neat foam trim options out there now. They may have something you could use.
Glenn



__________________
glennjanie is offline  
 
Reply With Quote Quick reply to this message
Old 05-31-2007, 05:19 PM  
Graham
Supporting Member
HRT_SUPPORTER.png
 
Graham's Avatar
 
Join Date: Mar 2006
Location: Halifax, Nova Scotia, Canada
Posts: 325
Liked 9 Times on 8 Posts

Default

Oakley; check out your Home Depot, as Glennsaid there are a number of options not the least of which are pre-formed and primed MDF corners.

__________________
Graham is offline  
 
Reply With Quote Quick reply to this message
Old 06-01-2007, 06:35 PM  
Square Eye
Senior Member
 
Square Eye's Avatar
 
Join Date: Jan 2006
Posts: 1,273
Liked 4 Times on 4 Posts

Default

A tall block is the absolute best way to deal with this transition.
When I have a situation like this, I take a few scraps and start looking at my options. Stick the scraps right to the wall and fasten them with finish nails just deep enough to hold them in place. Get your measurements with the scraps in place and you'll know what you're dealing with

__________________

[URL="http://www.houserepairtalk.com/announcement.php?f=39&a=6"][size=3]The Ten Commandments of House Repair Talk[/size][/URL]



[URL="http://home.bellsouth.net/p/s/community.dll?ep=16&groupid=289528&ck="]Square Eye's home page[/URL]

Square Eye is offline  
 
Reply With Quote Quick reply to this message
Old 06-03-2007, 04:13 AM  
MawMaw Di
Junior Member
 
Join Date: Mar 2007
Posts: 13
Default Glenn....a few questions on the foam crown moldings? Where can you purchase them?

Quote:
Originally Posted by glennjanie View Post
Hello Oakley:
You could consider an "L" shaped block laid onto the wall and join the crown moulding to each leg of the L. Don't forget there are some neat foam trim options out there now. They may have something you could use.
Glenn
Hi, I'm interested in the foam type crown moldings you've mentioned. Where can it be purchased? Are they easy to install? Our mini-kitchen renovation is still a work in progress (see my gallery photos). I would like to install new crown moldings, but we have no experience when it comes to installing them. Can these be purchased at Lowe's, Home Depot? Or, do you have to special order them online? Also, another question...we're thinking of triming out the soffit (?) that runs above our kitchen stove area (see our gallery photos)...it's the area where we took down some kitchen cabinets earlier. We want to run the soffit (or whatever it's called...as you can tell...we're not carpenters, ha!) across to the other wall & install a round pillar...give some artechitural (sp?) detail to our kitchen. Do you know how to affix the wood to the ceiling & surround it with drywall, etc.? Will we have to make a box type frame to do it? We're hoping it doesnt look too tacky, ha! My husband & I have viewed your family home gallery photos posted...your renovation work is just great! Would appreciate your comments. Thanks!
__________________
MawMaw Di is offline  
 
Reply With Quote Quick reply to this message
Old 06-03-2007, 04:30 AM  
MawMaw Di
Junior Member
 
Join Date: Mar 2007
Posts: 13
Default Square Eye, please read my question to Glenn (above) on molding installation!

Quote:
Originally Posted by Square Eye View Post
A tall block is the absolute best way to deal with this transition.
When I have a situation like this, I take a few scraps and start looking at my options. Stick the scraps right to the wall and fasten them with finish nails just deep enough to hold them in place. Get your measurements with the scraps in place and you'll know what you're dealing with
Square Eye, I would appreciate your comments on my posting questions to Glenn on molding intallation & building a frame to extend our soffit to install a decorative pillar. My husband & I have viewed your home photo gallery & your home renovation projects are excellent...great work! We would really appreciate your comments...as you can tell from our gallery photos of our mini-kitchen renovation...we're not expert carpenters, ha! This extention of the soffit is my idea...my husband doesn't think it can work. Do you? Like I said, it's mostly for decoration/artechitural (sp?) detail. Thanks much!
__________________
MawMaw Di is offline  
 
Reply With Quote Quick reply to this message
Old 06-03-2007, 11:16 AM  
glennjanie
Senior Member
 
Join Date: Mar 2006
Posts: 2,990
Liked 2 Times on 2 Posts

Send a message via AIM to glennjanie
Default

Helll MawMaw:
Yes the goam trim is available at Home Depot and Lowes. It can be installed with some types of construction adhesive (most adhesives have too much alcohol in them and will disolve the foam) and finish nails.
Your soffit should start with a strip (maybe 1 X 2s) screwed to the wall and one to the ceiling. If the ceiling joists run paralell to the strips you will need to add some blocking between the joists 2'o.c. and screwed in place. Short 1 X 2 struts, 2'o.c. for the front and bottom will hold the outside corner in place. Again, use construction adhesive and screws on the framing and drywall. Screws don't upset things that are already in place and finished; whereas, nails and the banging of the hammer will cause cracks and splits in undesireable places.
Finally, the work shown is not mine but Square Eye's (my son) I taught him some things and he capitalized on that and left me in the dust. He's really good, very meticulous and I am very proud of him.
Glenn

__________________
glennjanie is offline  
 
Reply With Quote Quick reply to this message
Old 06-03-2007, 04:16 PM  
MawMaw Di
Junior Member
 
Join Date: Mar 2007
Posts: 13
Default

Hi Glenn,
Thanks so much for answering my questions! We really appreciate it! We will for sure use screws, the size lumber, etc. you've suggested. We'll also go look at the foam crown molding & will make sure we don't use an adhesvie with a high alcohol content. Oh, does it come primed already & can we paint it? When we get this all done...I'll post another photo. I just hope it all works out like I see the image in my mind, ha! Also, how do you attach a pillar...construction anhesive to the top & bottom pieces? I'm sure we'll have to trim it to height, too...right? Well...again, thanks so much for your "info"!! You & your son (Square Eye) are very talented carpenters...I just think his house's front porch, deck & gazebo are so pretty! You both, keep posting your comments & your home project photos...they're great!! I look forward to reading all your posts...thanks again!
MawMaw Di (from Louisiana)

__________________
MawMaw Di is offline  
 
Reply With Quote Quick reply to this message
Old 06-03-2007, 06:51 PM  
glennjanie
Senior Member
 
Join Date: Mar 2006
Posts: 2,990
Liked 2 Times on 2 Posts

Send a message via AIM to glennjanie
Default

Hi MawMaw Di:
Yes, the foam trim is primed and ready to paint.
The column will have instructions with it; they vary some so I will let them do the talking.
Glenn

__________________
glennjanie is offline  
 
Reply With Quote Quick reply to this message
Old 02-06-2008, 11:04 AM  
BLZBUB
Junior Member
 
Join Date: Feb 2008
Posts: 14
Default So many options

Decorator's Supply Co. in Chicago has everything under the sun. Don't bother visiting their web site unless you've got a few hours to kill.



__________________
BLZBUB is offline  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Finally... New Project Questions - Crown Moulding jpeterson Walls and Ceilings 5 11-08-2008 09:21 AM
dark wood trim and crown moulding leecurran1 General Home Improvement Discussion 1 07-19-2008 01:48 PM
dark wood trim and crown moulding leecurran1 General Home Improvement Discussion 0 07-18-2008 11:09 PM
Crown moulding per foot labor cost? TaskBoy Carpentry and Woodworking 0 07-13-2008 01:59 AM
Nailing crown moulding? TaskBoy Carpentry and Woodworking 4 06-11-2008 08:21 PM