DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Carpentry and Woodworking > Custom Cabinet business taking questions




Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old 02-17-2006, 08:37 AM  
Maurers Custom Cabinetry
handcrafted cabinetry
 
Maurers Custom Cabinetry's Avatar
 
Join Date: Feb 2006
Posts: 4
Default Custom Cabinet business taking questions

Hello, my name is scott maurer. I'm a 4th generation cabinet maker experienced in kitchen and furniture design & fabrication. Wanted to offer any advice that I could to those of you with interests in kitchen remodeling and/or other room cabinetry. We are located in Perkasie, Pa. for those of you that are local, please stop in. We are currently constructing a new showroom that is directly attached to our shop and will be offering several lines of "stock" cabinetry as well as handcrafted items.

thank you for taking the time to read this post. Am happy to oblige in any way possible.



__________________
Maurers Custom Cabinetry is offline  
 
Reply With Quote Quick reply to this message
Old 02-21-2006, 02:25 AM  
TxBuilder
HRT_LIFETIMESUPPORTER.png
 
TxBuilder's Avatar
 
Join Date: Feb 2005
Posts: 1,677
Liked 5 Times on 5 Posts
Likes Given: 4

Default

Welcome! I am sure you will get quite a few questions over time. Tell us a little about your business. Have any pictures of your work?



__________________
TxBuilder is offline  
 
Reply With Quote Quick reply to this message
Old 02-21-2006, 04:59 AM  
Maurers Custom Cabinetry
handcrafted cabinetry
 
Maurers Custom Cabinetry's Avatar
 
Join Date: Feb 2006
Posts: 4
Default

Thank you for the welcome. Hoping to help in any way i can. I have found that in the last few years kitchen design as well as cabinet quality has become less than adequate. Most folks really dont realize what the possiblities are when designing and should be better educated consumers when it comes to cabinet construction and functionality. Photos of our work are posted in our gallery.

Thanks again,
Scott

__________________
Maurers Custom Cabinetry is offline  
 
Reply With Quote Quick reply to this message
Old 03-05-2006, 06:10 PM  
papargbear
Junior Member
 
Join Date: Mar 2006
Posts: 1
Default Question

I have a question for you. I have a custom dual-sink cherry vanity in my bathroom with a pinkish laminate top. The top's edges are trimmed in cherry. I'd like to replace the laminate with a more modern-looking laminate. Is there a way to remove the laminate without losing the cherry trim? I don't imagine I can just put new laminate over the old alminate, right? Any suggestions? Thanks.

__________________
papargbear is offline  
 
Reply With Quote Quick reply to this message
Old 03-06-2006, 06:40 AM  
Maurers Custom Cabinetry
handcrafted cabinetry
 
Maurers Custom Cabinetry's Avatar
 
Join Date: Feb 2006
Posts: 4
Default

That is a delicate situation. First determine if the cherry molding is perfectly flush with the laminate surface. If the molding is slightly above laminate you might be able to apply a sheet over top. If not you might have to very gingerly remove the molding to do what you would like.

You can try and find a local cabinet maker to match the color of your vanity with new cherry molding in case you incur damage. That is exactly why we offer color matching, sometimes it allows folks to rework a piece that they cannot or dont want to replace.

It is possible for us to assist you if you cant locate someone to color match for you. Not knowing if your close to us or not, it is possible to mail us a piece of your molding so we can match the color as well as the profile and we can ship back to you replacement pieces.

Would be more than happy to help any way that we can.

thank you,
scott maurer

__________________
Maurers Custom Cabinetry is offline  
 
Reply With Quote Quick reply to this message
Old 03-22-2006, 12:24 AM  
remodelinMo
Junior Member
 
Join Date: Mar 2006
Posts: 1
Default warping doors

I am building a kitchen in Missouri, the doors are varying widths of beech glue jointed, cut square, no panels, stiles or rails. The problem I am having is that after I had clamped and rough sanded the doors, the weekend came. When I got back to work on monday, I noticed that about 4 or 5 of the 27 doors had pretty severe warping. Now I made sure to alternate the grain patterns in the wood, and I laid the doors flat before I left for the weekend.
What I did to hopefully solve this particular problem is to clamp all of the doors together and place in a warm place for a week. This seemed to work decent, but the problem didn't completely abolish, there is still some slight warping on many of the doors, but fortunately, you can't tell once they're installed because I was able to adjust the hinges so that each door sat flat.

Also, I bought the wood from a reputable dealer (Liberty Hardwood), and they assured me that the lumber had all been kiln dried.

My question, is, is there a way to prevent the warping of these doors before, during, or after building them that I perhaps missed?

Also, is it possible to get edge banding to adhere properly(iron on kind) to MDF core sheet goods? Or do I need to change to a different core in the future? Thankyou for your help in advance.

__________________
remodelinMo is offline  
 
Reply With Quote Quick reply to this message
Old 03-23-2006, 03:30 PM  
glennjanie
Senior Member
 
Join Date: Mar 2006
Posts: 2,990
Liked 2 Times on 2 Posts

Send a message via AIM to glennjanie
Default

It sounds like you were able to remedy the warping just fine, but on the next set you make it would be beneficial to run some wood across the grain in some manner. There are several ways to do that; tounge and groove a piece across the top and bottom, screw and glue a piece across the back near top and bottom, etc. Wood is wonderful stuff but has to be controlled to keep the desired shape and size.

__________________
glennjanie is offline  
 
Reply With Quote Quick reply to this message
Old 03-23-2006, 08:27 PM  
inspectorD
Housebroken
HRT_MODERATOR.png
 
inspectorD's Avatar
 
Join Date: Dec 2005
Location: Litchfield, CT
Posts: 3,986
Liked 103 Times on 88 Posts
Likes Given: 227

Default When you go from shop to job...

I know its hard to believe... I was a shop rat in my past..
We did custom cabinets from a-wood to swiss pear...

One thing my boss did was to check the humidity levels in the house before we brought ANY cabinets to the job.
He would find out that the sheetrockers would want the heat totally cranked to dry things out. Thats exactly what would happen to our prefinished doors.. they would warp if the house was to dry or if the different humidity level was to drastic.

The hard part is going from shop to house.

All the old timers had the shops on site, why do you think all those old mansions are in good shape woodwork wise!!

LISTEN TO THE O"L TIMER"S....They have forgoten more than I know........

InspectorD

__________________

Just My
Made in the

inspectorD is offline  
 
Reply With Quote Quick reply to this message
Old 04-14-2006, 01:26 AM  
bobo60
Junior Member
 
Join Date: Jan 2006
Posts: 6
Default Polyurathane Kitchen Cabinets?

hello,

i have a question about my kitchen cabinets. i just recently bought the house i live in now. it was remodeled just before i bought it and the kitchen cabinets are brand new, and made of very nice oak with pine shelving. they looked like they were stained with a light teak colored stain, look very nice. i want to keep them looking nice, especially due to the runoff u get on the cabinets direrectly below the sinks. would it be a good idea to coat them with polyurathane? this should protect the stain from fading, and the wood, right??? thank u in advance for any suggestions

bob

__________________
bobo60 is offline  
 
Reply With Quote Quick reply to this message
Old 04-14-2006, 08:57 PM  
milehigh_woodcrafter
Member
 
Join Date: Apr 2006
Posts: 65
Default

remodelinmo

you'd have to better describe "warping". wood usually bows, cups, or twists. if you cupped, check the grain, if you twisted, check the grain. One way to abolish this is to rough mill you lumber and separate it on stickers so it can grow to the climate. "warm" weather doesn't do much for your wood. remember face, edges, ends. Don't be afraid to face-join your hardwoods, it may be crucial.



__________________

If you wanna hang with me bring a rope.

milehigh_woodcrafter is offline  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Kitchen cabinet build questions Rembrandt Carpentry and Woodworking 5 04-20-2010 03:19 AM
Base Cabinet Dilemma Browse General Home Improvement Discussion 9 01-19-2010 08:29 AM
Looking for Custom Cabinet with LEDS coolmike Electrical and Wiring 1 07-12-2007 10:33 AM