DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Carpentry and Woodworking > wood cutting




Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old 05-13-2011, 07:03 AM  
sisyphus
Senior Member
 
Join Date: Apr 2011
Location: orange county, ny
Posts: 127
Default wood cutting

is there a secret to cutting wood more precise? whenever I'm cutting, there always seems to be inconsistencies in my cutting. I use a quick framing square when cutting, but sometimes I have to recut or use shims. also I found out recently that not everything is what is marked on home depot 2x4studs. some where a little longer than 8' and a couple were actually cut a couple of inches shorter. when I checked the ends they showed that someone had cut them. I assumed that these were returned items.



__________________
sisyphus is offline  
 
Reply With Quote Quick reply to this message
Old 05-13-2011, 08:05 AM  
nealtw
Contractor
 
Join Date: Nov 2010
Location: vancouver, b.c.
Posts: 9,893
Liked 813 Times on 726 Posts
Likes Given: 1404

Default

studs should be 92 1/4 Canada. or 92 5/8 US. 8 foot length of lumber are about 96 1/4



__________________
nealtw is online now  
 
Reply With Quote Quick reply to this message
Old 05-13-2011, 08:08 AM  
nealtw
Contractor
 
Join Date: Nov 2010
Location: vancouver, b.c.
Posts: 9,893
Liked 813 Times on 726 Posts
Likes Given: 1404

Default

If the saw has been dropped a few time the table may not be square to the blade, the the quick sq. will not help in this case.

__________________
nealtw is online now  
 
Reply With Quote Quick reply to this message
Old 05-15-2011, 06:30 AM  
DrHicks
Big Hog
 
Join Date: Oct 2010
Location: Omaha, NE
Posts: 102
Liked 1 Times on 1 Posts

Default

Quote:
Originally Posted by sisyphus View Post
is there a secret to cutting wood more precise? whenever I'm cutting, there always seems to be inconsistencies in my cutting. I use a quick framing square when cutting, but sometimes I have to recut or use shims. also I found out recently that not everything is what is marked on home depot 2x4studs. some where a little longer than 8' and a couple were actually cut a couple of inches shorter. when I checked the ends they showed that someone had cut them. I assumed that these were returned items.
You were the unfortunate recipient of a dishonest man's screw job. 2x4 studs cost less than $2 each. Why anybody would jack with them, and cut them, then return them as if they were simply excess, is beyond me. What is wrong with people?!?!?!

Beyond that, accurate cutting requires decent tools and a careful hand & eye.
__________________
DrHicks is offline  
 
Reply With Quote Quick reply to this message
Old 05-25-2011, 07:37 AM  
sailingaway
Junior Member
 
Join Date: May 2011
Location: Douglasville, GA
Posts: 3
Default

Might sound elementary and if it does, I apologize. But remember to take the thickness of the blade into account. If you measure and draw a line be sure to measure again to determine where on the line you should cut. If you cut on the wrong side, you will be probably at least an 1/8" off. This can lead to a lot of inconsistency.

__________________
sailingaway is offline  
 
Reply With Quote Quick reply to this message
Old 07-01-2011, 09:39 PM  
losttool
Junior Member
 
Join Date: Jul 2008
Posts: 8
Default measuring tape

I take my measuring tape everytime I go to buy wood. Sometimes the wood is in the wrong stack and after I find a straight piece it is the wrong length.

__________________
losttool is offline  
 
Reply With Quote Quick reply to this message
Old 07-30-2011, 11:43 AM  
BrianKiernan
Member
 
Join Date: Aug 2010
Posts: 42
Default

Quote:
Originally Posted by sailingaway View Post
Might sound elementary and if it does, I apologize. But remember to take the thickness of the blade into account. If you measure and draw a line be sure to measure again to determine where on the line you should cut. If you cut on the wrong side, you will be probably at least an 1/8" off. This can lead to a lot of inconsistency.
This is a good point
__________________

Good Luck,
Brian
[URL="http://www.install-crown-molding.com"][COLOR="Blue"]http://www.install-crown-molding.com[/COLOR][/URL]

BrianKiernan is offline  
 
Reply With Quote Quick reply to this message
Old 08-14-2011, 11:19 AM  
BridgeMan
Senior Member
 
BridgeMan's Avatar
 
Join Date: Aug 2011
Location: Cottage Grove, Oregon
Posts: 738
Liked 75 Times on 67 Posts

Default

Measure twice, cut once.

__________________
BridgeMan is offline  
 
Reply With Quote Quick reply to this message
Old 08-18-2011, 08:40 PM  
Snav
Junior Member
 
Join Date: Aug 2011
Location: Cabot, Arkansas
Posts: 16
Default

I found that after dropping my saw several times the blade spindle was knocked crooked. I had to then adjust the angle of the blade to be just beyond "0" - a slight degree - to cut square to the surface.

For lengths being off-square per the run of your saw - get a better, longer T-square and use it in the same direction every time and see if it works better for you.

Use a pen - not a marker. The fatness of a marker tip can cause problems and weep.

And just don't trust that anything in a box store which is pre-cut just because it says it is cut precisely. Precision takes more care than what a crude factor saw mill ususally dedicates it's time to for box stores - their bigger concern is getting the wood sliced, not measured accurately every single time - their blades get out of whack and they change them or adjust them only when it's necessary.

__________________

I'm a giiirl - The local hardware store is my shopping mall ;)

Snav is offline  
 
Reply With Quote Quick reply to this message
Old 08-24-2011, 02:46 PM  
nealtw
Contractor
 
Join Date: Nov 2010
Location: vancouver, b.c.
Posts: 9,893
Liked 813 Times on 726 Posts
Likes Given: 1404

Default

Saw mills always cut lumber a little longer 1/4 to 3/4 depending on the mill. Precut studs are usually very good but the finger jointed precut studs are often done in a re-man mill and the quality can drop right off. Then you have to watch for studs shipped to the wrong market, Canada and the US have a different standard. 92 1/4 in Canada or 92 5/8 in the US.
As hard as you try you will always end up with rough framing. Top and bottom plates will shrink as they dry out and depending on how wet they were at the mill will end up drying to different thickness. This can easily shrink some walls by 1/4" and other walls not so much. Dimentional lumber like 2x10 used for a header can sometime shrink in height up to 1/4 inch.
This is why everyone hates framers.



__________________
nealtw is online now  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Tips for cutting through stucco Outbacker Bricks, Masonry and Concrete 4 04-06-2009 05:48 AM
Cutting tile on a wall Andrew12valve General Home Improvement Discussion 1 03-30-2009 10:32 PM
Cutting bricks on hearth? TaskBoy Bricks, Masonry and Concrete 2 06-03-2008 07:38 AM
Cutting panel doors Outbacker Windows and Doors 3 03-14-2007 07:44 AM
gyprock cutting paulh Introductions 1 08-28-2006 02:52 PM