DIY Home Improvement, Remodeling & Repair Forum > Appliances > HVAC > Change to Return Air Ducting OK?




Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old 11-27-2012, 04:55 PM  
jjjtttggg
Junior Member
 
Join Date: Nov 2012
Posts: 1
Default Change to Return Air Ducting OK?

My house has a mostly finished basement. We have an additional area that we're looking to finish out as well. Ceiling height to the floor joists above is a touch over 7 feet, which is great, but in the area we want to refinish, the furnace air return duct drops that to about 6' 4". That's still not bad, but it's not 7 feet! The duct goes from a floor grate near the bottom of the stairs on the first floor above, across the ceiling of the area I want to refinish, about 4 feet or so, and then through a brick wall to the furnace. Just before it enters the brick wall, the duct opens up from 8 x 20 or so, to about 16 by 20.

Here's my idea... I'm thinking I could possibly just remove the duct altogether. If I leave the floor grate above in place, open to the basement below, and put a grille across the opening as the duct goes through the brick wall, everything will look great and I'll have my full 7+ feet of ceiling height, but will the heating system still work right? The furnace would draw on the basement space rather than on the area at the base of the stairs on the floor above. It seems to me the basement space would naturally then just draw on the upstairs through that now open floor register, and to some extent through the kitchen and down the stairs. All of that seems totally fine to me. The basement is bone dry, with a solid slab throughout, and totally sealed from the outdoors. We've just installed a radon mitigation system that is working well, so I'm not concerned about that. There are three supply registers in the basement that today return up the stairs and around through the kitchen to the floor grate. It seems like the new setup would probably make those supplies work a little better with a teeny bit less load on the fan as result.

So what am I missing? Would this work? Any problems it might cause?

Thanks in advance for any feedback,

J



__________________
jjjtttggg is offline  
 
Reply With Quote Quick reply to this message
Old 11-28-2012, 10:34 AM  
nealtw
Contractor
 
Join Date: Nov 2010
Location: vancouver, b.c.
Posts: 9,318
Liked 730 Times on 651 Posts
Likes Given: 1278

Default

Welcome to the site. An open hole between floors is a free run for fires and not a good idea.
You might look at dividing it in half between upstairs and down. For the upstairs one you could remove the duct and put a piece of sheet metal against the joists and add a few 2x4s on edge and drywall that. You would still have 80".

__________________
nealtw is offline  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Water heater. To change or not to change? IZZY Plumbing Forum 5 01-21-2012 10:04 AM
hot air solar collector ducting gleni Green Energy and Sustenance Living 0 02-24-2011 11:42 AM
Is small, pliable ducting available? dpedsea HVAC 2 05-12-2009 01:53 PM
HRV ducting in attic dalyman0 HVAC 0 10-21-2008 06:40 PM
moving the hvac ducting import monkey HVAC 0 08-17-2007 12:36 PM