DIY Home Improvement, Remodeling & Repair Forum > Appliances > HVAC > Easy Access through a 24x24 return duct




Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old 04-27-2014, 07:46 PM  
drewdin
Junior Member
 
Join Date: Aug 2012
Posts: 392
Liked 26 Times on 23 Posts
Likes Given: 79

Default Easy Access through a 24x24 return duct

The 24"x24" return is my access to the attic and i have to remove the grill every time i need to get up there. Right now its just four screws into through the sheetrock onto the studs holding it on.


I'm nervous that over time the usage is going to destroy the ceiling and wear the holes.

What can i replace or add to the ceiling to make it a last and maybe even be a quick disconnect?

Thanks



__________________

Last edited by drewdin; 04-27-2014 at 07:57 PM.
drewdin is offline  
 
Reply With Quote Quick reply to this message
Old 04-27-2014, 10:20 PM  
nealtw
Contractor
 
Join Date: Nov 2010
Location: vancouver, b.c.
Posts: 10,277
Liked 850 Times on 759 Posts
Likes Given: 1466

Default

Are you saying you have an open grill between the house and attic?



__________________
nealtw is offline  
 
Reply With Quote Quick reply to this message
Old 04-28-2014, 10:13 AM  
drewdin
Junior Member
 
Join Date: Aug 2012
Posts: 392
Liked 26 Times on 23 Posts
Likes Given: 79

Default

Not exactly, its the return for the central AC but its also my access to the attic. Here it is without the grill installed or the holes drilled yet.

2013-12-15-11.44.53.jpg  
__________________
drewdin is offline  
 
Reply With Quote Quick reply to this message
Old 04-28-2014, 10:34 AM  
nealtw
Contractor
 
Join Date: Nov 2010
Location: vancouver, b.c.
Posts: 10,277
Liked 850 Times on 759 Posts
Likes Given: 1466

Default

I would just go for another access, that way you could insulate that and seal it as you now are loosing air and moisture into the attic. Are your ceiling joist or rafters 24" on center.

__________________
nealtw is offline  
 
Reply With Quote Quick reply to this message
Old 04-28-2014, 04:11 PM  
kok328
Supporting Member
HRT_SUPPORTER.png
 
Join Date: Nov 2007
Location: Grand Blanc, MI
Posts: 2,196
Liked 112 Times on 97 Posts
Likes Given: 64

Default

I think your looking for a solution for both the grille and the duct.
There are several hardware quick detach options for the grille but, for the duct?
I see handles up there, are you good with that design?
For the Grille:
Hinged grille, magnets, etc .....
What ever you put up there I see the opening is framed out so you can go right through the drywall into some solid wood.

__________________
kok328 is offline  
 
Reply With Quote Quick reply to this message
Old 04-29-2014, 11:10 AM  
drewdin
Junior Member
 
Join Date: Aug 2012
Posts: 392
Liked 26 Times on 23 Posts
Likes Given: 79

Default

Hi Guys,

Yes I framed out the opening along with a frame around the duct work with some handles so it would sit level and have a seal along with being easy to move. My question is more about the grill and how I can make it a quick disconnect. Are there any products you recommend?

Thanks again!

__________________
drewdin is offline  
 
Reply With Quote Quick reply to this message
Old 04-29-2014, 11:43 AM  
nealtw
Contractor
 
Join Date: Nov 2010
Location: vancouver, b.c.
Posts: 10,277
Liked 850 Times on 759 Posts
Likes Given: 1466

Default

You could install screw in anchors and then use machine screws
https://www.mcfeelys.com/sub_category.aspx?id=45391
I stll think you have to do more for sealing and insulating for the winter.

__________________
nealtw is offline  
 
Reply With Quote Quick reply to this message
Old 04-29-2014, 07:00 PM  
beachguy005
Senior Member
 
Join Date: Sep 2012
Posts: 194
Liked 57 Times on 51 Posts

Default

It depends on the frame that's on the grill. I would probably just get two small hinges for one side of the frame and a sliding barrel bolt latch for the opposite side.

__________________
beachguy005 is offline  
 
Reply With Quote Quick reply to this message
Old 04-30-2014, 10:55 AM  
drewdin
Junior Member
 
Join Date: Aug 2012
Posts: 392
Liked 26 Times on 23 Posts
Likes Given: 79

Default

The grill has a small inset and four screw holes, one in each corner. I never thought of using hinges, that's a good idea. I'll have to check the grill and see if it would work.

I do plan on sealing and insulating the return for winter, maybe using that magnetic sheet to cover the hole. I like those inserts you have linked above, looks like they are build for hard wood, would they work good in soft wood too? Thanks again



__________________

Last edited by drewdin; 04-30-2014 at 11:00 AM.
drewdin is offline  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Cold Air Return open under my siding, no duct, normal? Scarfone HVAC 22 11-20-2012 01:03 PM
Need Easy Way Irfan Roofing and Siding 9 09-18-2012 02:10 PM
Help with return air duct gasbie HVAC 0 06-19-2011 09:06 AM
crawl access problem usernamex Bricks, Masonry and Concrete 12 01-26-2011 09:46 PM
Easy fix hopefully intimidate Plumbing Forum 1 01-12-2010 03:54 PM