DIY Home Improvement, Remodeling & Repair Forum > Appliances > HVAC > "Fan on" option on thermostat not working




Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old 06-12-2014, 12:10 AM  
Emac
Junior Member
 
Join Date: Jan 2014
Posts: 9
Default "Fan on" option on thermostat not working

Trying to figure out why the "on option" for fan only on thermostat is not working. We moved in this house in december, so we only used the heating so far. The house is quad with 2 furnaces and 2 ac units. Since is not hot enough for ac i just tried to use the fan only option, so i put the heat and ac on off. One fan works, one doesn't, but the ac works on both units. We checked the wires on the wall, for the thermostat, they are all conected. Any sugestions? By the way, my hubby turned the pilot light off, for both furnaces, i don't know if it has anything to do with that.



__________________
Emac is offline  
 
Reply With Quote Quick reply to this message
Old 06-12-2014, 05:42 AM  
kok328
Supporting Member
HRT_SUPPORTER.png
 
Join Date: Nov 2007
Location: Grand Blanc, MI
Posts: 2,179
Liked 104 Times on 91 Posts
Likes Given: 61

Default

Set the thermostat well above or below the current temp using either heat or cool mode. Then try the "ON" for the thermostat. If this doesn't work then it might be that they didn't wire in the fan.
I can tell you more if you can answer the following:

How many wires are attached to the back of the thermostat(3,4,5)?
What colors are the wired attached to the back of the thermostat (red, green, white, yellow, black)?
What terminals are they attached on the back of the thermostat (R,C,Y,W,Y1,W2,G, etc...)?
Same information as above but, this time we want to look inside the air handler where the thermostat wires connect.



__________________
kok328 is offline  
 
Reply With Quote Quick reply to this message
Old 06-12-2014, 08:15 AM  
Emac
Junior Member
 
Join Date: Jan 2014
Posts: 9
Default

There are 4 wires, white, blue, green and red, all conected.
White conected at W, blue conected at Y, green conected at G, and red at R.
Was the blue suppose to be conected at B?
I cannot try the fan with the heat, since the furnace is off, pilot is off too. But it seems the fan works with the ac. But if i put the thermostat on off and put the fan on, nothing happens.
Thank you

__________________
Emac is offline  
 
Reply With Quote Quick reply to this message
Old 06-12-2014, 11:25 AM  
Wuzzat?
Banned
 
Join Date: Jan 2010
Posts: 2,328
Liked 167 Times on 154 Posts
Likes Given: 94

Default

Almost certainly you'll need a multimeter and a schematic. And sometimes the stat wires change colors inside the wall.

To test the stat independently of the system you'll need a 24 vac transformer and load [like a resistor from Radio Shack]. The stat is just switches controlled by temperature and the user's wishes.

If you just screw around with the wires you could damage something but you may not know it.
This is more confusing than house wiring but mistakes with these systems don't usually cause globs of molten copper to become airborne.

__________________

Last edited by Wuzzat?; 06-12-2014 at 04:42 PM.
Wuzzat? is offline  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Difference between "baseboards" and "moulding" panzerfaust0 Walls and Ceilings 8 01-18-2012 01:55 AM
System running Hot while set to "Cool" & "Off" halogen49 HVAC 7 03-06-2011 04:42 PM
Furnace not shutting off when thermostat switched to "heat" rasilun HVAC 1 01-06-2010 02:12 PM
Totaline thermostat blinking "Heat On" before the fan comes on. Maybeitwillwork HVAC 1 01-24-2009 09:20 PM
"Giant" hot water tank stoped working Xilbus Plumbing Forum 3 04-30-2008 06:48 AM