DIY Home Improvement, Remodeling & Repair Forum > Appliances > HVAC > Heat flame problem




Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old 11-24-2008, 08:10 PM  
Daryl
Member
 
Join Date: Sep 2005
Posts: 80
Default Heat flame problem

Have a Goodman furnace, no AC. Made in 1991 Installed 1992. 80 % High eff. This thing is driving me nuts!! Starting last year every once in a while the burners would not light clear across, say only 3 out of five for the first few tries then they would all kick in and heat up the house as usual. THie season it came to the point the thing would shut down after several tries and not fire up at all. then maybe an hour later it would fire up fine. I have cleaned the jets, replaced the air induction blower, cleaned the gas tube, replaced the gas valve and checked the voltage to the solenoid an valve 24.7 volts. Darn thing just acts like there isn't enough gas pressure getting through the valve. THis is a propane setup and I have installed the LP spring. What am I missing!? I know the hard surface igniter is working right or the valve wouldn't be getting the 24 volt current. Yes I have propane! (heh heh ) 400 gallon tank at 65%
DAryl



__________________

Last edited by Daryl; 11-24-2008 at 08:13 PM.
Daryl is offline  
 
Reply With Quote Quick reply to this message
Old 11-25-2008, 10:46 AM  
kok328
Supporting Member
HRT_SUPPORTER.png
 
Join Date: Nov 2007
Location: Grand Blanc, MI
Posts: 2,195
Liked 109 Times on 95 Posts
Likes Given: 64

Default

Isn't the hard surface ignitor suppose to be 120VAC?



__________________
kok328 is offline  
 
Reply With Quote Quick reply to this message
Old 11-25-2008, 01:19 PM  
glennjanie
Senior Member
 
Join Date: Mar 2006
Posts: 2,990
Liked 2 Times on 2 Posts

Send a message via AIM to glennjanie
Default

Hello Daryl:
You may want to check the heat exchanger for leaks. Using LP gas seems to burn out the exchanger tubes more quickly than natrual gas would. It is about 16 years old now and 12 to 20 years is the normal economic life of a furnace.
Check the wiring diagram for a limit switch that detects the leaking exchanger.
Glenn

__________________
glennjanie is offline  
 
Reply With Quote Quick reply to this message
Old 11-29-2008, 04:41 PM  
Daryl
Member
 
Join Date: Sep 2005
Posts: 80
Default

Figured it out!! Finally broke down and called the repairman. Found out the burners were rusted and not firing! Duh! Seems like I missed that one! Glenn , the heat exchanger was replaced about 6 years after furnace installation. The basement is quite humid during the spring -summer and fall due to stacked stone walls (house built in 1900) and a front porch slab slanted toward the house instead of pitched away.
Daryl

__________________
Daryl is offline  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Dryer heat problem reininop General Appliance Discussion 7 08-26-2009 08:50 AM
refig icemaker heat coil problem seismo1951 General Appliance Discussion 7 01-25-2009 08:14 PM
Electric Heat Pump & Programmable Thermostat John Greeb HVAC 2 01-09-2009 09:01 PM
problem with blower on hydronic heat jlyons HVAC 1 11-10-2008 12:57 PM
unequeal heat pump/air handler tonnage howie89 HVAC 6 06-19-2008 09:32 AM