DIY Home Improvement, Remodeling & Repair Forum > Appliances > HVAC > PLEASE HELP! AC drain pipe caused flood




Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old 09-06-2009, 11:09 PM  
slpstang02
Junior Member
 
Join Date: Sep 2009
Posts: 1
Default PLEASE HELP! AC drain pipe caused flood

Ok here is the deal.

My AC handler has a SafetT Switch incase of clogged drain.

Well i noticed my AC was continuously shutting off after about 10 minutes of running and house was hot. I pulled the top part out where you can insert bleach. As soon as i pulled it out water flowed up and over and then bounced up and down at the rim. I read numerous posts about using a wet vac inside and out.

So i grabbed the wet vac and sucked alot of water out of both inside and out. Looked in no water. Turned AC back on. Worked for about 2 days. CLogged again so i tried vac again. No luck.

Well i had to due something to keep air running here in florida with wife and kids home. So i pulled out Safe T switch and installed a pvc pipe with an elbow and down spout and scrwed it in. It allowed the water to dump out the secondary drain where the safet switch was. I had to open the panel to allowe air in so it would not creat a suction and keep the water in. It does the job of allowing air to run and fills a bucket quick.

Now down to the real drama. My house is a two story. Air handler is on second floor. I read somewhere someone had said to attach a garden hose and flush the line out. So i installed a shut off valve on the drainage pipe so water and air could not go back into the drain pipe. It also allowed a tight seal.

I installed a screw on cap to attach to the hose and connected it to a piece of pvc pipe and put it into the downspout where you would put bleach.

Wife turned on hose for about 8 seconds. I felt alot of resistance and then i heard water flowing out of the downstairs bathroom air vent/ water was shut off and i had a huge mess to clean.

After using a circular saw and sawzaw cutting the floor boards up on the second floor i located the draininge pipe. eventually i located the leak. The leak was at the first elbow piece coming from the down spout directly under the air intake hose thing. The water pressure caused the elbow piece to seperate from the drain pipe. it appeared at first that the installer did not glue them together. but after looking further it looked like there was glue inside the pipe. could the water pressure casue the pipe to break away the cement?

secondary why would my pipes be so clogged that water pressure from a hose could not clear the pipe and cause the joint to burst?

PLEASE HELP! What do i do? I tried blowing into the pipe but i get some much resistance the air shoots back out at me.

please please please help me.

thank you.



002.jpg   003.jpg   004.jpg   005.jpg   006.jpg  

__________________
slpstang02 is offline  
 
Reply With Quote Quick reply to this message
Old 09-07-2009, 08:24 AM  
woodchuck
Senior Member
 
Join Date: Jul 2008
Location: Tuscaloosa, Al
Posts: 246
Liked 17 Times on 16 Posts

Default

I recently had the same problem. I could blow through mine from outside and I had to do it three times before it finally started draining. I think the crud just settled back down and stopped it up again.

Maybe put the shop vac on the drain where it drips outside and it will eventually suck the clog out without the mess of blowing into it.



__________________
woodchuck is offline  
 
Reply With Quote Quick reply to this message
Old 09-07-2009, 09:10 AM  
kok328
Supporting Member
HRT_SUPPORTER.png
 
Join Date: Nov 2007
Location: Grand Blanc, MI
Posts: 2,185
Liked 105 Times on 92 Posts
Likes Given: 61

Default

Water pressure should not blow apart a properly attached joint.
You might be dealing with some type of insect nest that is blockin the flow.
Try feeding a fish tape from each end of the drain to clear the clog.

__________________
kok328 is offline  
 
Reply With Quote Quick reply to this message
Old 09-08-2009, 12:59 PM  
handyguys
Senior Member
 
handyguys's Avatar
 
Join Date: Feb 2008
Location: USA
Posts: 815
Liked 1 Times on 1 Posts

Send a message via Skype™ to handyguys
Default

Also - not sure of exactly what's going on. Just an observation, that valve in the picture is closed.

__________________

The Handyguys Podcast [url]http://www.handyguyspodcast.com[/url]

handyguys is offline  
 
Reply With Quote Quick reply to this message
Old 09-08-2009, 04:56 PM  
glennjanie
Senior Member
 
Join Date: Mar 2006
Posts: 2,990
Liked 2 Times on 2 Posts

Send a message via AIM to glennjanie
Default

Hello SLPStang:
I vote for KOK's remedy; snake the pipe out and put a 'running trap' on the lower end to keep the insects from getting into the pipe. The trap will drown them and the condensate will wash them out as the come along, being that near the end of the pipe.
Glenn



__________________
glennjanie is offline  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Can't clear galvanized pipe drain. Replace? DaringDamsel Plumbing Forum 6 07-08-2009 09:01 AM
Flange/Tail Pipe Removal - Bathroom Sink Drain Ted Plumbing Forum 2 02-03-2009 01:17 PM
Toilet drain pipe slope. npelzer Plumbing Forum 6 12-14-2007 10:34 PM
Risk of Explosion When Soldering Drain Pipe? travelover Plumbing Forum 3 10-22-2007 04:39 PM
Depth of drain pipe under slab Mudball Plumbing Forum 4 06-10-2006 07:34 PM