DIY Home Improvement, Remodeling & Repair Forum > Appliances > HVAC > Tacos, BGs & baseboard oh my




Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old 01-10-2014, 03:58 PM  
rokosz
Junior Member
 
Join Date: Jun 2013
Posts: 25
Liked 6 Times on 6 Posts
Likes Given: 5

Default Tacos, BGs & baseboard oh my

One of my zones isn't circulating. Was fine a few days ago (zone not used constantly), been in service for 6 years.

Being somewhat ignorant I replaced the cartridge in the Taco 007. no change. disassembled it again and tested power to the impeller. aok. re-assembled.

Argo control board lights properly when the tstat calls, taco works. what the 'ell else can it be? Ahhh what about that red thing over there?

yes being somewhat ingnorant i thought the red thing was on the return -- not the supply. (esp since the tacos are warm/hot and that is not. I found a doc at Xylem/BG site for the flo contorl valve sa1 3/4 it shows an exploded parts diagram and talks about cleaning.

Does blockage/failure of the valve seem to be the culprit?
It certainly seems so -- no leaks anywhere, working ok a few days ago. Not a complicated installation -- But I don't have isolators on both sides of the valve -- so I'll have to drain -- not fun in the winter.

Anybody know why it would require cleaning? or have any pointers on the process? thanks, bryan



__________________
rokosz is offline  
 
Reply With Quote Quick reply to this message
Old 01-15-2014, 02:11 PM  
rokosz
Junior Member
 
Join Date: Jun 2013
Posts: 25
Liked 6 Times on 6 Posts
Likes Given: 5

Default

For all time, let it be known here:

A simple hammer (tap(ping)) on the illustrious BG Flo-control solved the circulation issue.

It kind of solved itself too-- I'd shut all the isolators (3 --2 @ return, one into the BG). Called for service. Open the balls, hit the stat -- and flow gently down the stream. Tech explained they usually give a shot or two with a hammer to the BG.

I'd begun the attempt to "rebuild" or at least clean out the valve -- but didn't like tugging on all that copper and stopped without even beginning to loosen the packing nut or plug. Tech poo-pooed attempting any removal of the plug or valve assembly.

I'd also tried turning the valve control open and closed a few times prior to isolating the zone.

so combo of isolation and valve or one or the other? Next time I'll try tapping it



__________________
rokosz is offline  
inspectorD Likes This 
Reply With Quote Quick reply to this message
Old 01-15-2014, 07:35 PM  
nealtw
Contractor
 
Join Date: Nov 2010
Location: vancouver, b.c.
Posts: 10,335
Liked 860 Times on 768 Posts
Likes Given: 1486

Default

Sorry you didn't get any help here, thanks for the update.

__________________
nealtw is offline  
 
Reply With Quote Quick reply to this message
Old 01-16-2014, 06:28 PM  
inspectorD
Housebroken
HRT_MODERATOR.png
 
inspectorD's Avatar
 
Join Date: Dec 2005
Location: Litchfield, CT
Posts: 4,077
Liked 124 Times on 104 Posts
Likes Given: 304

Default Yes

Thanks for the Update!! It's good to learn something new.I mean, who knew you just needed a hammer to fix your parts....usually ends up with extra parts.

__________________

Just My
Made in the

inspectorD is offline  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Baseboard Transition dzuroff Walls and Ceilings 2 03-31-2011 12:26 PM
Help with wall behind baseboard Hurryheathen General Home Improvement Discussion 4 10-17-2010 03:31 PM
Insulation behind baseboard? Razztjazz Insulation and Radiant Barriers 1 07-07-2010 05:48 AM
Baseboard question jeiowa01 Flooring 1 07-10-2009 09:46 PM
One HOT baseboard! MarkBrown HVAC 1 01-07-2008 04:25 PM