DIY Home Improvement, Remodeling & Repair Forum

DIY Home Improvement, Remodeling & Repair Forum (http://www.houserepairtalk.com/forum.php)
-   HVAC (http://www.houserepairtalk.com/f8/)
-   -   Trane XE90 LED Troubleshooting Codes (http://www.houserepairtalk.com/f8/trane-xe90-led-troubleshooting-codes-5733/)

furmanator 12-16-2008 08:30 PM

Trane XE90 LED Troubleshooting Codes
 
Have a Trane XE90 and it's blowing air but the Igniter will not go on. The boards LED is flashing 4 times. I moved in 2 years ago and replaced the igniter about 2 months ago. The prevous owner did not leave me with the manual with the codes. If anyone out there knows what the codes mean It sure would be apprieciated, it's going to be a two dog night. Only problem is I have a Jack Russell who provides too little heat and a Bullmastiff that pushes me out of bed.

kok328 12-17-2008 06:12 AM

Check on the back of the removable panels or ignition control module to see if there is a diagnostics chart.

furmanator 12-17-2008 06:23 AM

I did and there was nothing there

FmrLCpl 10-17-2009 02:22 PM

Quote:

Originally Posted by furmanator (Post 26086)
I did and there was nothing there

4 flashes -- Open High Limit Device

whatever that means.

kok328 10-19-2009 03:59 PM

High limit switch is a device to shut down the system in the event of an over-heating condition in the combustion chamber. There are dozens of types of switches being used. Some are manually resetable and some are not. The resetable types will have a small red button in the center of them between the two wires. Press this button in and try the system again. If it is not the resetable type then you might get lucky by tapping on it to get it to unstick. Otherwise you'll have to replace it. Just be sure to replace it with one of the identical ratin. The spec print on these is microscopic and will require a pair of young eyes or a magnifying glass to see.

hoadle 11-23-2009 06:53 PM

My sister bought the house about year ago, last week she toll me The circulation blower does not turn off –always running (Trane XE90 gas furnace units in the house)
Although the thermostat is set on 'Off' vs. 'Heat' or 'Cool' and fan ( I mean circulation blower) is on 'Auto', the fan runs constantly.
The sight glass on the furnace shows a red light is off.
(Look like gas furnace & air condition unit is working final only problem the circulation blower is run continuous)
I disconnect the Thermostat control of base the circulation blower still running is tell me the Thermostat control not control the circulation blower
I check HPS/PS2 (High Limit SW) & LPS/PS1 (low limit SW) + inducer housing limit SW. All had continuity (normal close switch)
I check Vaccum switch is no continuity (normal open switch) when I turn on the heater & check vaccum switch is had continuity.
I switch to air condition (unplug blue wire for heater circulation blower) is circulation blower turn on about 30 second & shut off (I hear 2 cliks at relay one begin & 30 second late is turn off the circulation blower.
I can’t find the Trane XE90 gas furnace manual online but I folow the dirgram at housing door check all thing above. Maybe I missing some step from Troubleshoot to check out the circulation blower setup.
Please let me know what wrong my sister gas furnace

Furnacexr95 11-25-2009 07:03 AM

Can someone please help: How much doest it cost to replace a Trane XE90 with a Trane XR95, 100,000 BTU same physical size and hook ups?

Furnacexr95 11-25-2009 08:55 AM

Trane XR95, 100,000 BTU
 
Can someone please help: How much does it cost to replace a Trane XE90 with a Trane XR95, 100,000 BTU same physical size and hook ups?

jtplanktin 12-05-2009 08:06 AM

I just had this. It was dirty filters. I replaced them. Very easy. My filters are directly above the heating chamber, so it was getting too hot, and tripping the high limit switch (4 blinks is the "Open High Limit Device").

They're $4 each at Home Depot. I needed 3 of them.

thanksagain 11-10-2011 08:36 AM

XE 90 High Limit Switch reset and location
 
Quote:

Originally Posted by kok328 (Post 35876)
High limit switch is a device to shut down the system in the event of an over-heating condition in the combustion chamber. There are dozens of types of switches being used. Some are manually resetable and some are not. The resetable types will have a small red button in the center of them between the two wires. Press this button in and try the system again. If it is not the resetable type then you might get lucky by tapping on it to get it to unstick. Otherwise you'll have to replace it. Just be sure to replace it with one of the identical ratin. The spec print on these is microscopic and will require a pair of young eyes or a magnifying glass to see.


Would like to reset/replace my high limit switch but not sure where it is, I do see a sensor on the fire box with two wires, is that it? But no reset switch on it.


All times are GMT -6. The time now is 12:40 AM.