DIY Home Improvement, Remodeling & Repair Forum > Appliances > HVAC > Vent / Register Repair




Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old 09-15-2011, 05:09 PM  
dfradeneck
Junior Member
 
Join Date: Sep 2011
Location: Oak Park, Michigan
Posts: 1
Default Vent / Register Repair

I'm not sure if I'm posting in the right place for this, so please forgive me as this is my first post.

I recently purchased my first home (hurray!). I am quickly learning that the previous owner was a Do-It-Yourselfer but where he and I differ is that I like to make sure that what I am doing is right before I attempt something. He seemed to fly by the seat of his pants with a "If it works, it works" kind of attitude.

We have set our sights on the living room and one of the first thing that I realized was that the registers (air vents) looked about 20 years older than me. I decided that when we got around to the painting portion I was going to replace them. So here we are, last night, I pull out my handy screw driver to take them off so I can bring them up to my hardware store to ask questions when low and behold, the vents are actually secured to the walls with... wait for it... 3/4 inch thick of CAULK. The previous owner had never checked to make sure they were the right size, filled in the gaps with the caulk and called it a day. So cursing his inability to do anything right, 45 painful minutes later I had the registers off.

So, now I have my vents off, I measure the holes and head up to the hardware store to buy new ones. I like them, they're shiney and new and aren't covered by 19 layers of multicolored paint. I bring them home and attempt to fit them in but oops, they don't fit. But wait, I measure the holes before I bought them, I double checked them and I found the problem. While I had purchased the right size the vent holes were bent! Inspecting a little further I see the real problem.

Once again, the previous owners worksmanship shows its ugly head. The metal vents are surrounded by... putty, simply patch putty... and they have been bent. There is so much putty surrounding these bent vents that the registers that I purchased that should fit don't. The registers aren't far off, we're talking about a few millimeters of difference.

My question, how do I fix these vents so that my registers fit? Should I gouge out all the terrible that the previous owner slapped on there, attempt to work the vents back into their appriopriate shape, and then slap some sort of patch around them to fill in the gunk I just had to dig out, or would that ultimately be exactly what the last guy did?

Any suggestions / guidence would be greatly appreciated. Keep in mind I'm a first time home buyer and money is a little tight, so while the right thing to do might be to hire a company to come in a fix my entire vent work, that simply isn't going to happen...

Once again, any advice is greatly appreciated.



__________________
dfradeneck is offline  
 
Reply With Quote Quick reply to this message
Old 09-15-2011, 11:35 PM  
nealtw
Contractor
 
Join Date: Nov 2010
Location: vancouver, b.c.
Posts: 9,781
Liked 803 Times on 716 Posts
Likes Given: 1369

Default

If the money is tight I think you are just digging it out, other wise you are cutting into walls.

__________________
nealtw is offline  
 
Reply With Quote Quick reply to this message
Old 09-16-2011, 02:42 AM  
BridgeMan
Senior Member
 
BridgeMan's Avatar
 
Join Date: Aug 2011
Location: Cottage Grove, Oregon
Posts: 738
Liked 75 Times on 67 Posts

Default

I suspect you will be able to install the new registers with considerably better workmanship than the previous owner, so just bite your lip and go for it!

I could write a book about all of the junk-quality work done on previous properties I've owned (how does electrical wiring splices wrapped with Scotch tape, no wire nuts, sound?, or how about black pipe used for a hot water bath tub connection? You get the idea). Nothing ever will be perfect, but the key to living happily is successfully addressing the challenges presented to you, and moving forward with better solutions.

Over the years, I've best summed up my attitude about such things--T.O.C. That stands for "Thrive On Challenges."

__________________
BridgeMan is offline  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Register blowers user1234 Decorating and Design 5 04-21-2011 04:14 PM
Moving hot air register..... nick13 General Home Improvement Discussion 1 06-15-2010 08:52 PM
Bathroom exhaust fan. Is it ok to vent it through attic & up to ridge vent? lola123go General Home Improvement Discussion 9 05-13-2010 03:58 PM
Register placement Dalmus HVAC 2 02-01-2010 07:27 PM
New Register shacarr12 Introductions 2 02-05-2008 04:47 PM