DIY Home Improvement, Remodeling & Repair Forum > Appliances > HVAC > York stellar furnace acting up





Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old 12-29-2012, 03:33 PM  
Gbmike1972
Junior Member
 
Join Date: Dec 2012
Location: Indianapolis, Indiana
Posts: 7
Default York stellar furnace acting up

I have a York stellar furnace (Model # p1udd12n07601a) and it will turn on the vent fan and the igniter the burners will light for a few seconds and then shut off . the vent fan continues to run, but then after 5 minutes the igniter starts glowing and it reignites. only to shut right back down. I have removed the flame sensor and cleaned it. checked the fusable link. any help would be greatly appreciated



__________________
Gbmike1972 is offline  
 
Reply With Quote Quick reply to this message
Old 12-29-2012, 06:33 PM  
rogerknapp
Junior Member
 
Join Date: Dec 2012
Posts: 9
Default

replace flame senser



__________________
rogerknapp is offline  
 
Reply With Quote Quick reply to this message
Old 12-29-2012, 07:28 PM  
Gbmike1972
Junior Member
 
Join Date: Dec 2012
Location: Indianapolis, Indiana
Posts: 7
Default

Thanks I will try that. Can you buy those at Lowes or Home depot?

__________________
Gbmike1972 is offline  
 
Reply With Quote Quick reply to this message
Old 12-30-2012, 01:25 PM  
rogerknapp
Junior Member
 
Join Date: Dec 2012
Posts: 9
Default

probably going to have to go to a york dealer to get the part take your model and serial number with you

__________________
rogerknapp is offline  
 
Reply With Quote Quick reply to this message
Old 12-30-2012, 09:14 PM  
Gbmike1972
Junior Member
 
Join Date: Dec 2012
Location: Indianapolis, Indiana
Posts: 7
Default

Thank you so much for your help.

__________________
Gbmike1972 is offline  
 
Reply With Quote Quick reply to this message
Old 12-30-2012, 09:58 PM  
joechuckg
Junior Member
 
Join Date: May 2012
Posts: 8
Default

Replacing the flame sensor won't fix your problem. Does your furnace have a circuit board? Does the gas valve have 24 volts across it as it drops out if so replace valve. If 24 volts drops out as flame drops out replace control board. Make sure rollout switches aren't opening.

__________________
joechuckg is offline  
 
Reply With Quote Quick reply to this message
Old 12-31-2012, 10:16 AM  
Gbmike1972
Junior Member
 
Join Date: Dec 2012
Location: Indianapolis, Indiana
Posts: 7
Default

There is no circuit board on my model. I removed the old flame sensor and cleaned it. It worked fine for a couple days then started acting up again. Do you know what terminals I test across to check the valve?

__________________
Gbmike1972 is offline  
 
Reply With Quote Quick reply to this message
Old 01-02-2013, 10:39 AM  
Gbmike1972
Junior Member
 
Join Date: Dec 2012
Location: Indianapolis, Indiana
Posts: 7
Default

While working on my furnace I checked my drain hose for blockages. The plastic manifold that the combustion fan mounts to was cracked and leaking moisture. I cleaned it up and sealed with JB weld. Does anyone know the actual name of this part. So I can replace it.

__________________
Gbmike1972 is offline  
 
Reply With Quote Quick reply to this message
Old 01-02-2013, 03:25 PM  
Wuzzat?
Senior Member
 
Wuzzat?'s Avatar
 
Join Date: Jan 2010
Posts: 1,848
Liked 95 Times on 86 Posts
Likes Given: 55

Default

How old must a furnace be to not have a control board?

__________________
Wuzzat? is offline  
 
Reply With Quote Quick reply to this message
Old 01-03-2013, 09:32 AM  
ozone
Junior Member
 
Join Date: Nov 2010
Location: Shelby Twp., Michigan
Posts: 11
Liked 1 Times on 1 Posts

Default

Regarding your question in post #8.
If your refering to the plastic cover between the lower area of the heat exchanger and the inducer, (combustion fan). Then you are refering to the "collector box".



__________________
ozone is offline  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
York Stellar Plus NG furnace wont' stay running-HELP johnceberhardt HVAC 24 07-03-2012 05:18 AM
How to light a York Stellar Plus Furnace...PLEASE HELP carose HVAC 1 12-11-2009 08:20 PM
York Stellar Plus problem acbikeworks HVAC 4 10-19-2009 03:54 PM
York Stellar Plus wonít ignite rodge HVAC 24 01-11-2009 04:36 AM
York Stellar Furnace problem clayjthom HVAC 7 12-28-2008 02:58 PM